The present paper describes the results from experimental and theoretical modelling studies on the behaviour of continuous carbon fibre/polymer matrix composites subjected to a relatively low-velocity or high-velocity impact, using a rigid, metallic impactor. Drop-weight and gas-gun tests are employed to conduct the low-velocity and high-velocity impact experiments, respectively. The carbon fibre composites are based upon a thermoplastic poly(ether–ether ketone) matrix (termed CF/PEEK) or a thermoset toughened epoxy matrix (termed CF/Epoxy), which has the same fibre architecture of a cross-ply [0₃/90₃]_2slay-up. The studies clearly reveal that the CF/PEEK composites exhibit the better impact performance. Also, at the same impact energy of 10.5 ± 0.3 J, the relatively high-velocity test at 54.4 ± 1.0 m s⁻¹leads to more damage in both types of composite than observed from the low-velocity test where the impactor struck the composites at 2.56 m s⁻¹. The computationally efficient, two-dimensional, elastic, finite element model that has been developed is generally successful in capturing the essential details of the impact test and the impact damage in the composites, and has been used to predict the loading response of the composites under impact loading.

The quasi-static flexural and impact performance, up to projectile impact velocities of about 270 m s⁻¹, of fibre metal laminates (FMLs), which consist of relatively thin, alternately stacked, layers of an aluminium alloy and a thermoset glass fibre epoxy composite, have been investigated. The effects of varying (a) the yield strength, tensile strength and ductility of the aluminium alloy layer, (b) the surface treatment used for the aluminium alloy layers and (c) the number of layers present in the FML have been studied. It was found that increasing the strength of the aluminium alloy increases the quasi-static flexural strength of the FML, providing that good adhesion is achieved between the metal and the composite layers. Further, increasing the number of alternating layers of the aluminium alloy and fibre composite also somewhat increases the quasi-static flexural properties of the FML. In contrast, increasing the strength of the aluminium alloy had relatively little effect on the impact perforation resistance of the FML, but increasing the number of alternating layers of aluminium alloy and fibre composite did significantly increase the impact perforation resistance of the FML. The degree of adhesion achieved between the layers had only a negligible influence on the impact perforation resistance.

Carbon-fibre/epoxy-matrix composites used in aerospace and vehicle applications are often susceptible to critical loading conditions and one example is impact loading. The present paper describes a detailed experimental and numerical investigation on the relatively low-velocity (i.e. <10 m/s) impact behaviour of such composite laminates. In particular, the effects of the geometry of the impactor have been studied and two types of impactor were investigated: (a) a steel impactor with a hemispherical head and (b) a flat-ended steel impactor. They were employed to strike the composite specimens with an impact energy level of 15 J. After the impact experiments, all the composite laminates were inspected using ultrasonic C-scan tests to assess the damage that was induced by the two different types of impactor. A three-dimensional finite-element (FE) model, incorporating a newly developed elastic-plastic damage model which was implemented as a VUMAT subroutine, was employed to simulate the impact event and to investigate the effects of the geometry of the impactor. The numerical predictions, including those for the loading response and the damage maps, gave good agreement with the experimental results.

Polymeric foams are extensively used as the core materials in sandwich structures and the core material is typically bonded between relatively thin fibre-composite skins. Such sandwich structures are widely used in the aerospace, marine and wind-energy industries. In the present work, various sandwich structures have been manufactured using glass-fibre-reinforced polymer (GFRP) skins with three layers of poly(vinyl chloride) foam to form the core, with the densities of the foam layers ranging from 60 to 100 kg/m³. This study has investigated the effects on the quasi-static flexural and high-velocity impact properties of the sandwich structures of: (a) the density of the polymeric-foam core used and (b) grading the density of the foam core through its thickness. The digital image correlation technique has been employed to quantitatively measure the values of the deformation, strain and onset of damage. Under quasi-static three-point and four-point bend flexural loading, the use of a low-density layer in a graded-density configuration reduced the likelihood of failure of the sandwich structure by a sudden force drop, when compared with the core configuration using a uniform (i.e. homogenous) density layer. The high-velocity impact tests were performed on the sandwich structures using a gas-gun facility with a compliant, high-density polyethylene projectile. From these impact experiments, the graded-density foam core with the relatively low-density layer located immediately behind the front (i.e. impacted) GFRP skin was found to absorb more impact energy and possess an increased penetration resistance than a homogeneous core structure.