Conventional eddy-current sensors have the advantages of being contactless and having high bandwidth and high sensitivity. They are widely used in micro-displacement measurement, micro-angle measurement, and rotational speed measurement. However, they are based on the principle of impedance measurement, so the influence of temperature drift on sensor accuracy is difficult to overcome. A differential digital demodulation eddy current sensor system was designed to reduce the influence of temperature drift on the output accuracy of the eddy current sensor. The differential sensor probe was used to eliminate common-mode interference caused by temperature, and the differential analog carrier signal was digitized by a high-speed ADC. In the FPGA, the amplitude information is resolved using the double correlation demodulation method. The main sources of system errors were determined, and a test device was designed using a laser autocollimator. Tests were conducted to measure various aspects of sensor performance. Testing showed the following metrics for the differential digital demodulation eddy current sensor: nonlinearity 0.68% in the range of ±2.5 mm, resolution 760 nm, maximum bandwidth 25 kHz, and significant suppression in the temperature drift compared to analog demodulation methods. The tests show that the sensor has high precision, low temperature drift and great flexibility, and it can instead of conventional sensors in applications with large temperature variability.

The phase recovery module is dedicated to acquiring phase distribution information within imaging systems, enabling the monitoring and adjustment of a system’s performance. Traditional phase inversion techniques exhibit limitations, such as the speed of the sensor and complexity of the system. Therefore, we propose an indirect phase retrieval approach based on a diffraction neural network. By utilizing non-source diffraction through multiple layers of diffraction units, this approach reconstructs coefficients based on Zernike polynomials from incident beams with distorted phases, thereby indirectly synthesizing interference phases. Through network training and simulation testing, we validate the effectiveness of this approach, showcasing the trained network’s capacity for single-order phase recognition and multi-order composite phase inversion. We conduct an analysis of the network’s generalization and evaluate the impact of the network depth on the restoration accuracy. The test results reveal an average root mean square error of 0.086$\lambda$ for phase inversion. This research provides new insights and methodologies for the development of the phase recovery component in adaptive optics systems.

As the fields of aviation and aerospace optics continue to evolve, there is an increasing demand for enhanced detection capabilities in equipment. Nonetheless, in applications where both optical and mechanical constraints are stringent, the continuous expansion of optical aperture and focal length is impractical. Given the existing technological landscape, employing super-resolution algorithms to enhance the imaging capability of optical systems is both practical and highly relevant. This study capitalizes on using a 2D scanning galvanometer in optical systems to acquire micro-displacement information. Initially, an imaging model for optical systems equipped with a 2D scanning galvanometer was established, and the displacement vectors for both forward and sweep image motions were defined. On this foundation, we incorporated micro-displacement information that can induce high-frequency aliasing. Subsequently, the motion paths of the galvanometer were planned and modeled. To align image sequences with micro-displacement correlations, the Lucas–Kanade (L-K) optical flow method was employed with multi-layer pyramid iteration. Then, super-resolution reconstruction was performed using kernel regression techniques. Ultimately, we tested the algorithm on an aeronautical optoelectronic pod to evaluate its impact on optical resolution and imaging quality. Compared with the original images, the 16-frame image demonstrated a 39% improvement in optical resolution under laboratory conditions. Moreover, the algorithm exhibited satisfactory performance under both nighttime and daytime conditions, as well as during aerial tests.

Imaging using scattering media is a very important yet challenging technology. As one of the most widely used scattering imaging methods, speckle autocorrelation technology has important applications in several fields. However, traditional speckle autocorrelation imaging methods usually use iterative phase recovery algorithms to obtain the Fourier phase of hidden objects, posing issues such as large data calculation volumes and uncertain reconstruction results. Here, we propose a single-shot scattering imaging method based on the bispectrum truncation method. The bispectrum analysis is utilized for hidden object phase recovery, the truncation method is used to avoid the computation of redundant data when calculating the bispectrum data, and the method is experimentally verified. The experimental results show that our method does not require uncertain iterative calculations and can reduce the bispectrum data computation by more than 80% by adjusting the truncation factor without damaging the imaging quality, which greatly improves imaging efficiency. This method paves the way for rapid imaging through scattering media and brings benefits for imaging in dynamic situations.