Currently, there are different remediation technologies for contaminated soils, but the selection of the best technology must be not only the treatment efficiency but also the energy consumption (costs) during its application. This paper is focused on assessing energy consumption related to the electrochemical treatment of polluted soil with petroleum hydrocarbons. In the framework of a research project, two types of experiments were conducted using soil that was artificially contaminated with diesel fuel at the same level of contamination. The experimental conditions considered for each experiment were: different amounts of contaminated soils (6 kg and 18 kg, respectively), the same current intensity level (0.25A and 0.5A), three different contamination degrees (1%, 2.5% and 5%) and the same time for application of the electrochemical treatment. The remediation degree concerning the removal of petroleum hydrocarbons from soil increased over time by approximately 20% over 7 days. With regard to energy consumption, the results revealed that with an increase in the quantity of treated soil of approximately three times, the specific energy consumption decreased from 2.94 kWh/kg treated soil to 1.64 kWh/kg treated soil.
In agreement with European Union directives, the integrated management of municipal solid waste must be developed ensuring a balanced relationship between the streams of selective collection and the one regarding the residual waste. A theoretical scenario is made where the residual municipal solid waste is composed only of non‐recyclable fractions. An important aspect concerns the role of the organic fraction as selective collection can significantly decrease its content in the residual waste. This paper focuses on the planning, design and management consequences of this unsteady scenario. The treatments that are considered are: combustion, gasification, pyrolysis, integrated thermal plants, aerobic mechanical–biological treatments, anaerobic mechanical–biological treatments and other types of treatment. The considerations are based on the experience of the authors not only in terms of development of research but also in terms of transfer of the research results to the real scale, and knowledge of the state‐of‐the‐art of the sector.
Given the energy crisis and climate change due to pollution, and given that the largest emissions of greenhouse gases are produced by the energy industry, we must turn our attention to the efficient use of solar energy, which is the cleanest and most abundant of all renewable energies. In this paper, based on an analysis of the specialized literature, we studied the effect of dust accumulation on the surface of photovoltaic modules on some performance characteristics and on the efficiency of these panels and modules compared to the efficiency of clean modules. We analyzed the cause of dust accumulation and the influence of the tilt angles of the photovoltaic panels on the dust deposition rate. We highlighted the influence of atmospheric temperature, solar radiation, wind speed, and relative humidity depending on the density of the dust deposited on the surface of the photovoltaic panel, and we found a decrease in the efficiency of the panel based on the increase in dust density for slightly high values of solar radiation, wind speed, and relative humidity. We highlighted the reduction in CO2 emissions by replacing electricity from fossil fuels with solar energy. The efficient use of solar energy is a solution for the decarbonization of the energy sector.
Soils contaminated with organic substances is an important issue across Europe: In some areas, these are the main causes of pollution, or the second after contamination from waste disposal. This paper included an experimental application that compared three methods of remediation of contaminated sites, based on electric fields: A single treatment (electroremediation); and two combined treatments, phyto-electrochemical and electrooxidation (a combination of chemical treatment and a DCT—direct current technology). The contaminated soil was taken from a former industrial area devoted to oil refining, located between two roads: The one national and the other one for industrial use. Nine soil samples were collected at two depths (0.2 and 0.4 m). The initial characterization of the soil showed a density of 1.5 g/cm³ and a moisture of about 20%; regarding grain size, 50% of the soil had particles with a diameter less than 0.08 mm. The electrochemical treatment and electrooxidation had an efficiency of 20% while the two combined methods had efficiencies of 42.5% for electrooxidation (with H2O2) and 20% for phyto-electroremediation (phyto-ER) with poinsettias.
Polycyclic aromatic hydrocarbons (PAHs) are considered hazardous pollutants due to their negative impact on the environment and human health. PAHs can accumulate and be retained in the soil, so PAH pollution is a worldwide problem. This review paper highlights the sources of PAH soil pollution, factors affecting the bioavailability of PAHs in soil, and soil bioremediation methods, as well as the advantages and limitations of the application of these methods. Aspects regarding the impact of the application of surfactants are presented in order to obtain good bioavailability during PAH bioremediation. Bioremediation techniques of soil polluted by these hydrocarbons are addressed: phytoremediation, rhizoremediation, composting, vermiremediation, micoremediation, and electrokinetic bioremediation of PAH-polluted soils. A comprehensive overview of bioremediation technologies for PAH-polluted soils is needed so that the right soil remediation technology is chosen. It has been observed the bioremediation of contaminated soils through rhizoremediation proved to be an effective process, the future of organic pollutants in interaction with plants and microbes must be researched. Vermiremediation, electrokinetic bioremediation, and microcomposting are effective processes for treating soils in situ. Phytoremediation is a sustainable and ecological method of PAH depollution. It improves soil fertility by releasing different organic matter in the soil, and it can be applied on a large scale.