safa polat

Dr. safa polat


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 May 2022 in Ceramics International
Verified
Journal Article
Closed access
SPsafa polat
safa polat
DFDana Faris
Dana Faris

12 April 2019 in Journal of Composite Materials
Verified
Journal Article
Closed access
PDF file
SPsafa polat
safa polat
YSYavuz Sun
Yavuz Sun
EÇEngin Çevik
Engin Çevik
HCHendrik Colijn
Hendrik Colijn
ETEmre Turan
Emre Turan
The present study aims to produce graphene nanoplatelet-coated B4C ceramic particle using semi-powder method and to investigate the effect of graphene nanoplatelets on wear and corrosion performance of Al–Si-based metal matrix hybrid composites. For this purpose, first graphene nanoplatelets at different ratios (0.25, 0.5, and 1 vol.%) were coated to the surfaces of B4C particles and then the Al–Si alloy was infiltrated into the reinforcements by gas pressure infiltration method. The characterization of graphene nanoplatelet-coated B4C powders and its composites was carried out by X-ray diffraction, differential scanning calorimetry, scanning electron microscope, and transmission electron microscope analysis. Tribological properties were investigated by reciprocating ball-on-flat method under three different loads (10–20–40 N) in a dry environment. The corrosion resistance was carried out with Tafel polarization method in 3.5% NaCl solution. Characterization results show that graphene coated on the B4C surface was successfully achieved by semi-powder method. After infiltration process, a new phase formation was not observed, but porosity increased with the increase of graphene content. When the boron carbide surface was coated with 0.5vol.% graphene, it was determined that the specific wear resistance increased by 55% and the corrosion resistance decreased by 12%.

1 October 2019 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
SPsafa polat
safa polat
YSYavuz Sun
Yavuz Sun
EÇEngin Çevi̇k
Engin Çevi̇k
HCHendrik Colijn
Hendrik Colijn

19 September 2022 in Journal of Materials Science: Materials in Electronics
Verified
Journal Article
Closed access
PDF file
SPsafa polat
safa polat
MMMuwafaq Mashrah
Muwafaq Mashrah

25 August 2023 in Nanomaterials
Verified
Journal Article
Open access
PDF file
CLCHIKH SIDI EL MOKHTAR MOHAMED LEFDHIL
CHIKH SIDI EL MOKHTAR MOHAMED LEFDHIL
SPsafa polat
safa polat
HZHuseyin Zengin
Huseyin Zengin
The synthesis of zinc oxide (ZnO) was accomplished from zinc borate (Zn3B2O6) minerals to be used as electrodes in supercapacitor applications. The concentrations of obtained zinc (Zn) metal after treatment with hydrochloric acid (HCl) were determined by atomic absorption spectroscopy (AAS). Direct synthesis of ZnO on a nickel (Ni) foam surface was conducted by employing the hydrothermal technique using a solution with the highest Zn content. The results showed the successful synthesis of ZnO nanorods on the surface of Ni foam with an average wall size of approximately 358 nm. Cyclic voltammetry (CV) and galvanostatic charge–discharge (GCD) measurements revealed that the synthesized electrode exhibited battery-type charge storage characteristics, reaching a maximum specific capacitance of approximately 867 mF·cm−² at a current density of 2 mA·cm−². Additionally, the energy and power densities of the electrode at a current density of 2 mA·cm−² were calculated as 19.3 mWh·cm−² and 200 mW·cm−², respectively. These results exhibited promising performance of the single-component electrode, outperforming the existing counterparts reported in the literature.
1

12 February 2021 in Journal of Tribology
Verified
Journal Article
Closed access
PDF file
SPsafa polat
safa polat
YSYavuz Sun
Yavuz Sun
ECEngin C¸eVik
Engin C¸eVik
In this study, it was aimed to investigate the effects of reinforcements used for improving the thermal properties of AA6061 alloy on wear resistance. For this purpose, composites were produced by pressure infiltration method using ceramic microparticles (TiB2 and B4C) and graphene nanoparticles (GNPs). The produced composites were first characterized by porosity measurement, XRD and SEM analysis. Then, the wear behavior of was examined under three different loads (20-40-60N) with the reciprocating ball on flat method in dry environment. Specific wear rates were calculated according to Archard principle by measuring the depth and width of the traces after tests with a profilometer. Wearing mechanisms were determined with the help of optical and microstructure images. According to the obtained results, it was found that B4C + GNPs reinforced samples were more resistant to abrasion at low loads, but TiB2 + GNPs reinforced samples were higher at higher loads.