13 October 2023 in IEEE Transactions on Dielectrics and Electrical Insulation
Partial discharge (PD) causes different physical processes in different mediums, exciting acoustic signals with wide frequency distribution. And the attenuation and catadioptric process of the acoustic signal caused by the propagation medium weaken the acoustic signal and further complicate the characteristics. As a result, the characteristics of PD acoustic signals are closely related to the properties of insulating mediums. Therefore, it is necessary to select an appropriate acoustic sensor based on the characteristic of the PD acoustic signal. The optical acoustic sensing technology has high sensitivity, fast response speed and strong anti-interference ability, which is the most potential PD detection sensor, ensuring the safe and stable operation of power equipment. But the response characteristics of the sensor limited the accurate characteristic analysis of acoustic signals in the previous research. This paper reviewed the characteristics of PD acoustic signals in typical insulating mediums obtained by previous research, analyzed the optical acoustic sensor suitable for partial discharge detection, which aims at selecting the sensors suitable for PD detection of different types of power equipment based on the current sensor technology and prospecting the development direction of the optical acoustic sensor for PD detection.
5 June 2025 in International Journal of Hydrogen Energy
22 October 2020 in Journal of Physics D: Applied Physics
Knowledge of leader corona is the basis for long spark discharge modelling, which is critical to understand the underlying physics of lightning flashes and dielectric breakdown of long air gap widely utilized in power systems. This paper presents an accurate observation of the leader corona. The morphology of the leader corona region during the discharge was obtained using a high-speed camera and an image-enhanced charge-coupled device camera. Statistical results showed that the morphology of the streamer region varied at different discharge sub-phases. The first corona was a conical region with the average apex angle of 118.91°; the leader corona region behaved as a cone with an average vertex angle of 75.87° during the leader propagation process; the streamer area in the final jump was a combination of a cylinder and a cone with the average vertex angle of 82.61°. Noting that the obtained cone apex angle of the leader corona during the leader propagation phase was significantly smaller than that in photographical reports, and the observation results were related to the selected temporal resolution of the optical image apparatus. The discussion on the effect of the single-frame exposure time on observation results found that the average vertex angle of the conical streamer region gradually decreased with the decrease of the single-frame exposure time, and eventually tended to a stable value of about 75.96°. For comparison purposes, discharge experiments under two gap-distances demonstrated that on the premise of stable leader, the statistical distribution characteristics of the leader corona vertex angle were consistent, indicating the universal applicability to the simulation researches. Finally, it is found that the distortion of the electric field caused by the space charge explained the variation of the streamer area during the discharge process.
10 May 2025 in International Journal of Hydrogen Energy
15 July 2021 in IEEE Transactions on Instrumentation and Measurement
The measurement of ac/dc hybrid electric fields in converter transformers is important for the verification of electric field calculation model and the insulation optimization. Electro-optical (EO) sensors have obvious advantages for measuring strong electric fields, but their response characteristics and mechanisms under the action of ac/dc hybrid electric fields are not fully understood by researchers, which restricts a wide application of sensors. In this article, we first describe an improved dual-beam structure, which enables us to measure both ac and dc electric fields in oil simultaneously. Next, the complete output characteristics of the EO sensor under ac/dc hybrid electric field are obtained through experiments. The results show that measurement sensitivities of EO sensor under dc and ac electric fields are different; there is a coupling effect in measuring ac/dc hybrid electric fields: the increase of one electric field component will reduce the sensor's measurement sensitivity to the other electric field component, which is more obvious for a strong electric field. Finally, we propose the response mechanism with theoretical analysis. First, the sensitivity difference is due to the difference of electric fields inside EO crystal under ac and dc electric fields, and it is affected by the conductivity and dielectric constant of crystal and oil medium. Second, the optical nonlinearity of EO sensors under strong electric fields is the cause of coupling effect: the sensor's nonlinear modulation of a strong ac electric field will introduce coupling errors in measurement signal of the dc electric field and a strong dc electric field will move the zero point of the sensor's ac induction curve from the linear region to the nonlinear region, causing the ac sensitivity to decrease nonlinearly with the increase of the applied dc electric field. This article provides a measurement and analysis of EO sensors under ac/dc hybrid electric fields in an oil medium environment, which is beneficial to the wide application of EO sensors.
1 November 2024 in Journal of Physics D: Applied Physics
Flashover faults on gas insulated switchgear (GIS) insulators induced by metal particles occur frequently. Previous studies have obtained the characteristics of partial discharges (PDs) induced by metal particles on spacer surfaces, but these characteristics cannot explain the detection failure of ultra-high frequency (UHF) online monitoring. To enable further study of the PD characteristics induced by surface metal particles, the space electric field and a very-high-sensitivity pulse current (PC) measurement system were established. The electric field and PC characteristics of a PD induced by metal particle on the spacer surface of a 126 kV GIS were obtained. Two PD modes were found to be induced by surface metal particles. In addition to the typical pulse discharge (TP), there is a micro-discharge group (MG) mode with low apparent charge and long duration. The average apparent charge of the MG mode is approximately one-tenth of that of the TP at 0.4 pC. Its duration may extend to the millisecond level, causing significant distortion of the spatial electric field while hardly producing UHF signals. Moreover, increasing the applied voltage will increase the proportion of the MG within the total discharge, where this proportion can reach more than 90% before flashover, and the proportion of the discharge pulses that generates UHF signals is as low as 1%. The MG generation mechanism is analysed, the ion group stranded on the spacer surface by the TP changes the local electric field at the tip of the metal particle, which reduces the development length and apparent charge of the MG. Low apparent charge is cleared easily by the background electric field and thus the discharge interval is very short. This paper can provide an important basis for revealing the mechanism of GIS spacer surface discharge induced by metal particles and solving the effectiveness of PD monitoring devices.