Efficient hybrid PV/Wind energy generation is a challenge against fluctuating solar and wind speed conditions. The paper aims to analyze and improve the performance of an optimized and restructured hill-climbing Maximum Power Point Tracking (MPPT) method, called dP-P&O (Perturb and Observe), for fast-changing environmental conditions of a Hybrid PV/Wind Energy Conversion System (HPVWECS). In the first part of the paper, this technique is restructured and adapted for application in PV Systems (PVS) and Wind Energy Conversion Systems (WECS) where the duty cycle is the control action instead of the reference voltage. The experimental implementation of this technique, for a developed HPVWECS emulator, shows the performance limitation of this technique. To overcome these drawbacks, a proposed method simplified the schemes of the algorithm by considering the novel optimized dP-P&O scheme only, with the integration of a fuzzy logic scheduling controller for the duty cycle perturbation step size based on the power change and the previous duty cycle variation. The proposed MPPT controller is tested in the HPVWECS emulator experimental test bench, to evaluate its performance and robustness. The experimental results prove that the second proposed approach gives higher precision, which leads to an ameliorated energy quality and better performance and robustness, compared to the novel hybrid dP-P&O algorithm (first proposed approach), against different solar and wind environmental conditions and load change.
1 September 2024 in International Journal of Power Electronics and Drive Systems (IJPEDS)
Aerial robotics encompasses intricate kinematics and dynamics that govern the flight of quad-rotor systems. Among the various methods employed for flight control using microcontrollers like the ESP32 developed by ESPRESSIF; the proportional integral derivative (PID) controller stands out as a widely adopted approach. The ESP32 microcontroller offers a superior interface, delivering enhanced performance and response time, particularly in dynamic environments. This article delves into the implementation and viability of the ESP32 platform for communication with MATLAB/Simulink, as well as real-time data acquisition to control the attitude of quadcopter withe chassis F450. The PID controller was designed to specifically work with the ESP32 platform and rigorously tested on an actual quadcopter during flight operations. lastly, a comprehensive analysis of the data gained and empirical results from the physical model demonstrates that the proposed framework is effective.
1 June 2023 in International Journal of Power Electronics and Drive Systems (IJPEDS)
The diagnosis of wind energy conversion systems (WECS) turns out to be necessary because of their relatively high cost of operation and maintenance. Wind turbines are hard-to-access structures, and they are often located in remote areas. Therefore, a remote diagnosis (e-diagnosis) is required. This paper proposes an alternative approach for the e-diagnosis of a WECS based on the discrete wavelet transform (DWT) and frequency analysis of the aero generator stator currents. To validate this approach, real-time hardware in the loop (HIL) is used to simulate in real-time the mathematical model of the induction generator on the OPAL-RT OP5600 platform to generate the stator currents and the rotor speed. The DWT is applied to the current signal, to generate the DWT signal, which has a huge number of points that are not supported for direct transmission by the Arduino Mega RobotDyn because of its limited sample time. The absolute values of the DWT peak points (MDWT) are sent as point’s packages form to the diagnosis station via the ESP8266 integrated Wi-Fi board of the Arduino Mega RobotDyn to monitor the SCIG states and determine the number of broken bars.
1 December 2024 in International Journal of Power Electronics and Drive Systems (IJPEDS)
This paper introduces an approach decentralized to fault detection and isolation (FDI) in manufacturing systems using a Boolean discrete event model. The method incorporates diverse information sources to create distinct models for plant systems and control. The objective is to enhance the understanding of process operations by employing various representation tools tailored to each information source. It is to reduce the number of explosion problems combinatorial and detect faults in the shortest possible time. This comprehensive representation facilitates the fulfillment of three crucial diagnosis functions: detection, localization, and identification. The approach involves Boolean modeling of each process actuator along with its corresponding sensors, a temporal model based on fuzzy expectations of event occurrences, and a set of if...then rules. The goal of this decentralized approach minimize both the complexity and the manual construction effort required for the model. The paper demonstrates the effectiveness of this approach through an illustrative example involving manufacturing systems.