This paper presents a flexible microstrip low-pass filter (LPF) fabricated on a polyimide film substrate. The proposed flexible microstrip LPF with ten cascaded asymmetrical Pi-shaped defected ground structure (DGS) resonators are designed, simulated, manufactured, and measured. The simulation and experiment results demonstrate that the designed flexible microstrip LPF has a very sharp transition band, an ultra-wide stop-band (SB) and high rejection in SB performance compared with the existed microstrip LPFs with symmetrical and asymmetrical DGS. The proposed flexible LPF with ten cascaded resonators is with a compact size of 100 mm $\times2.6$ mm $\times0.254$ mm, a very low insertion loss of less than 1.9 dB under 2.2 GHz, and a wide SB from 2.7 to 12 GHz with the rejection of larger than 50 dB. The proposed flexible LPF has the potential to be used in wireless terminals to replace the traditional RF coaxial cable because it is very thin and has good transmission and filtering functions.
17 March 2022 in IEEE Transactions on Microwave Theory and Techniques
In this article, we present a novel dual-band bandstop filtering cable by surrounding inner wire with asymmetric bridge-connected spiral-shaped defected structure on outer conductor. The simulation results demonstrate that the proposed dual-band bandstop filtering cable can be modeled by two parallel RLC resonance circuits in cascade and the performance can be easily adjusted by changing the structural parameters. The well-designed dual-band bandstop filtering cable can be fabricated by core wire surrounding with polytetrafluoroethylene (PTFE) dielectric layer and polyimide defected conductor layer with asymmetric bridge-connected spiral-shaped defected structures. The proposed filtering cable with ten asymmetric bridge-connected spiral-shaped defected resonators on defected conductor layer has a compact size of diameter 1.66 mm and length 200 mm, and its insertion loss in experimental results is greater than 20 dB at 0.88 and 1.3 GHz. Compared with the traditional microstrip bandstop filter, the proposed dual-band bandstop filtering cable can achieve better stopband and passband performance within more compact size. In essence, it is a cable replacement technology, which can improve electromagnetic compatibility (EMC) performance at system level and equipment level, and has the potential to be widely used in wireless system.
The design and implementation of printed helical spiral antenna (PHSA) and helical printed inverted-F antenna (IFA) are presented for unmanned aerial vehicle (UAV) with global positioning system (GPS) L1 band (1.57 GHz) and telemetry communication frequency band (2.33 GHz) applications. The proposed antenna is miniaturized by co-winding the radiation elements on the same ceramic rod, surface covering by dielectric sealant, inserting a high permittivity dielectric load into the helical structure, turning and meandering the radiation element of PHSA into a spiral parallelogram structure. The PHSA and helical IFA antenna radiation elements are manufactured by silver pasted on the same hollow ceramic cylinder with a diameter of 12 mm and a height of 24.7 mm. The experimental and simulation results show that the proposed PHSA and IFA can achieve the gain of 0.05dB and 1.97 dB respectively and be suitable for GPS L1 band and telemetry communication frequency band (2.33 GHz) applications separately.
This paper presents a pioneering design of a distributed multiband bandstop filtering power transmission line with the primary objective of suppressing interference. The proposed design integrates sawtooth dumbbell-shaped defected structures and surface-mounted capacitors on the outer conductor, providing an efficient emulation of a noncontact method for a filtering circuit model. To achieve flexibility in performance adjustments, the design is based on simulated current distribution paths and an equivalent circuit model comprising multiple inductors and capacitors, enabling parameter modifications. The fabrication process entails encasing a core wire within a dielectric layer of polyethylene foam (PE) and a polyimide defected conductor layer (DCL) featuring the sawtooth dumbbell-shaped structures and capacitors. Two filtering lines, each measuring 8 mm in diameter and 1500 mm in length, are simulated, fabricated, and measured. Experimental findings indicate that the first filtering line, equipped with a surface-mounted capacitor of 680 pF, achieves suppression exceeding 20 dB at 42.6 MHz and 48.2 MHz. In comparison, the second line, featuring a surface-mounted capacitor of 22 nF, demonstrates a suppression of −5.62 dB at 8.13 MHz. These results affirm the effectiveness of the proposed filtering line in achieving the desired bandstop filtering characteristics across various frequency bands.
Electrical cables, often referred to as ‘blood vessels’ and ‘nerves’ of the industry, play a vital role in the connection of electrical devices. However, traditional cables that lack distributed filtering functions are usually the primary coupling path for electromagnetic compatibility (EMC) problems. An innovative design for a filtering cable, which incorporates insulated electrical wires coated with a specific defected conductor layer (DCL), enables it to achieve distributed filtering advantages along its axis. Microwave network analysis is employed to build the two-port network model of filtering cable, which efficiently analyzes the cascading characteristics of periodic or aperiodic filtering cables. To validate, the flexible printed circuit board (FPCB) with sawtooth dumbbell-shaped DCL and mounted by capacitors is wrapped around the stripped section of the coaxial cable to manufacture a multi-stopband filtering cable. Simulated and measured results demonstrate that the proposed filtering cable can be effectively suppressed in the stopband, which can be adjusted by changing the values of capacitors.