Xu Jiqing

Dr. Xu Jiqing

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 March 2023 in Sensors
Verified
Journal Article
Open access
PDF file
HYHengwei Yu
Hengwei Yu
LWLong Wang
Long Wang
XJXu Jiqing
Xu Jiqing
PCPatrick Yin Chiang
Patrick Yin Chiang
Direct time-of-flight (dToF) ranging sensors based on single-photon avalanche diodes (SPADs) have been used as a prominent depth-sensing devices. Time-to-digital converters (TDCs) and histogram builders have become the standard for dToF sensors. However, one of the main current issues is the bin width of the histogram, which limits the accuracy of depth without TDC architecture modifications. SPAD-based light detection and ranging (LiDAR) systems require new methods to overcome their inherent drawbacks for accurate 3D ranging. In this work, we report an optimal matched filter to process the raw data of the histogram to obtain high-accuracy depth. This method is performed by feeding the raw data of the histogram into the different matched filters and using the Center-of-Mass (CoM) algorithm for depth extraction. Comparing the measurement results of different matched filters, the filter with the highest depth accuracy can be obtained. Finally, we implemented a dToF system-on-chip (SoC) ranging sensor. The sensor is made of a configurable array of 16 × 16 SPADs, a 940 nm vertical-cavity surface-emitting laser (VCSEL), an integrated VCSEL driver, and an embedded microcontroller unit (MCU) core to implement the best matched filter. To achieve suitably high reliability and low cost, the above-mentioned features are all packaged into one module for ranging. The system resulted in a precision of better than 5 mm within 6 m with 80% reflectance of the target, and had a precision better than 8 mm at a distance within 4 m with 18% reflectance of the target.

14 March 2023 in IEEE Photonics Technology Letters
Verified
Journal Article
Closed access
HYHengwei Yu
Hengwei Yu
SZShenglong Zhuo
Shenglong Zhuo
YWYifan Wu
Yifan Wu
LWLong Wang
Long Wang
TXTao Xia
Tao Xia
PCPatrick Yin Chiang
Patrick Yin Chiang
This letter presents a novel fully integrated dToF system-on-chip ranging sensor based on a SPADs array. The sensor is made a configurable array of $16\times16$ SPADs, a 940nm VCSEL, a co-design VCSEL driver and embedded DSP core. To suitable different ranging scenarios with high reliability and low cost, the above mentioned are all packaged into one module for ranging. However, the package of coverglass can cause Xtalk, which have a negative impact on ranging. In order to reduce the influence of Xtalk on ranging. This letter proposes a real-time Xtalk calibration circuit system, which can automatically adjust the laser pulse width, when Xtalk and target bins are mixed together. And also to mitigate the effect of SPAD jitter on the Xtalk bins width, an adjustable bias voltage charge pump circuit is adopted to realize the accurate adjustment of pixel SPAD’s bias voltage. The system has been turned out with precision of better than 5mm within 6m in 80% reflectance of target, still with a precision better than 8mm at a distance within 4m in 18% reflectance of target.

19 October 2023 in IEEE Photonics Technology Letters
Verified
Journal Article
Closed access
ZLZhihong Lin
Zhihong Lin
YLYuan Li
Yuan Li
XJXu Jiqing
Xu Jiqing
MYMengxin Yu
Mengxin Yu
PCPatrick Yin Chiang
Patrick Yin Chiang
This paper presents a voltage-mode direct time-of-flight (DToF) driver with high resolution auto-peak-power controller (APPC) and peak-current detector (PCD), utilizing on-chip oscilloscope (OCO) technology. The OCO supports both optical input for APPC and electrical input for PCD. The optical input detects laser diode (LD) peak power through photodiode (PD) first, and then feeds back to the boost converter to adjust laser diode supply voltage (LDVCC) to reach the target peak optical power. The electrical input detects the peak current of the LD to prevent the APPC from adapting to excessive output caused by the abnormal operation of the PD or LD. The X-coordinate of OCO has an 11-bit precision, and the Y-coordinate also has a 11-bit precision. It can detect pulse widths ranging from 500 ps to 10 ns. The chip also integrates multiple power protection circuits for the boost converter. The test result shows that, the variation of optical power can be controlled within 2% in the temperature range of 25-85 °C with APPC function.

9 August 2023
Verified
Preprint
Open access
PDF file
YLYuan Li
Yuan Li
LHLi Hong
Li Hong
XJXu Jiqing
Xu Jiqing
PCPatrick Yin Chiang
Patrick Yin Chiang
This paper presents a voltage-mode direct time-of-flight (DToF) driver with high resolution auto-peak-power controller (APPC) and peak-current detector (PCD), utilizing on-chip oscilloscope (OCO) technology. The OCO supports both optical input for APPC and electrical input for PCD. The optical input detects laser diode (LD) peak power through photodiode (PD) first, and then feeds back to the boost converter to adjust laser diode supply voltage (LDVCC) to reach the target peak optical power. The electrical input detects the peak current of the LD to prevent the APPC from adapting to excessive output caused by the abnormal operation of the PD or LD. The X-coordinate of OCO has an 11-bit precision. It can detect pulse widths ranging from 500 ps to 10 ns. The test result shows that, the variation of optical power can be controlled within 2\% in the temperature range of 25-85 ℃ with APPC function.

2 March 2023 in Electronics Letters
Verified
Journal Article
Open access
XJXu Jiqing
Xu Jiqing
HYHengwei Yu
Hengwei Yu
YWYifan Wu
Yifan Wu
PCPatrick Chiang
Patrick Chiang
This letter presents a high frame rate and low area cost partial histogram scheme for d‐ToF depth imaging sensor based on SPAD. This scheme realizes high frame rate through a novel peak seeking algorithm based on gray code and pipeline operation that firstly adopted. Area cost is reduced by partial histogram and overlap is used to prevent data loss. Finally, a 24 bins partial‐histogram design is implemented by ASIC flow with a total area of 11724 μm 2 under 130 nm. FPGA flow is also used to verify feasibility. Compared with other known partial histogram schemes, proposed method has no data and frame rate loss.