A turbulent jet ignition engine enables operation with lean mixtures, decreasing nitrogen oxide (NO_X) emissions up to 92%, while the engine efficiency can be increased compared to conventional spark-ignition engines. The geometry of the pre-chamber and engine operating parameters play the most important role in the performance of turbulent jet ignition engines and, therefore, must be optimized. The initial experimental and 3D CFD results of a single-cylinder engine fueled by gasoline were used for the calibration of a 0D/1D simulation model. The 0D/1D simulation model was upgraded to capture the effects of multiple flame propagations, and the evolution of the turbulence level was described by the new K-k-ε turbulence model, which considers the strong turbulent jets occurring in the main chamber. The optimization of the pre-chamber volume, the orifice diameter, the injected fuel mass in the pre-chamber and the spark timing was made over 9 different operating points covering the variation in engine speed and load with the objective of minimizing the fuel consumption while avoiding knock. Two optimization methods using 0D/1D simulations were presented: an individual optimization method for each operating point and a simultaneous optimization method over 9 operating points. It was found that the optimal pre-chamber volume at each operating point was around 5% of the clearance volume, while the favorable orifice diameters depended on engine load, with optimal values around 2.5 mm and 1.2 mm at stoichiometric mixtures and lean mixtures, respectively. Simultaneous optimization of the pre-chamber geometry for all considered operating points resulted in a pre-chamber volume equal to 5.14% of the clearance volume and an orifice diameter of 1.1 mm.

This paper presented an experimental and numerical study of pre-chamber volume, number of orifices and orifice diameter influence on engine performance and emissions. All the measurements were performed on a single cylinder test engine at fixed engine speed of 1600 rpm, while engine load was varied by a change of the excess air ratio in the main chamber from a stochiometric mixture to a lean limit. The total of nine pre-chamber variants comprised three different pre-chamber volumes, two orifice number combinations (six and four orifices) and nine different orifice diameters. It was observed that the pre-chamber volume affects the indicated efficiency in a trend which is mostly independent of excess air ratio, with the efficiency gain between the best and worst results ranging from 1 to 4.4%. While keeping the same pre-chamber volume and the total cross-sectional area of the orifices, the larger number of orifices show better performance on two out of three investigated pre-chamber volumes, with the efficiency gains more pronounced at higher excess air ratios. Finally, on a fixed pre-chamber volume and number of orifices, the variation of orifice diameter leads to a trend in efficiency gains which favor larger orifice diameter. The comparison of the obtained efficiencies between all pre-chamber variants identified two pre-chambers, differing in each of the varied geometrical parameters, that show the best performance depending on excess air ratio range. On the other hand, a single variant which showed the worst performance on each excess ratio was identified. An additional investigation was performed by the application of the cycle-simulation model to quantify the share of emissions which are formed in the pre-chamber. The presented results showed that when PC volume is lowered, PC emission shares of NO_X and CO grow larger. The influence of orifice number and size has a minor effect on the pre-chamber emissions shares. The maximum PC emission shares of 54.8% and 80.6% are achieved at lean limit (λ = 2.2) for NO_X and CO, respectively. THC emission share, on the other hand, is not affected in a significant manner by either the pre-chamber geometry or operating conditions.

This paper presents an experimental and numerical evaluation of the pre-chamber induced HCCI combustion concept (PC-HCCI) in terms of engine performance, emissions, and controllability. In this concept, a spark-initiated combustion in the pre-chamber is utilized to trigger the kinetically controlled combustion of an ultra-lean mixture in the main combustion chamber. The experimental measurements were performed on a single-cylinder engine with a custom-made active pre-chamber. A high compression ratio of 17.5 was used, which limits the maximum achievable engine load due to high knocking tendency but enables both standard PCSI combustion (flame propagation) at very high dilution levels and HCCI combustion at reasonable intake temperatures. The analysis of combustion characteristics and the resulting performance is performed at indicated mean effective pressures (IMEPs) of 3.5 and 3.0 bars, and three different intake temperatures of 80 °C, 90 °C, and 100 °C. The variation in engine load was achieved by adjusting the excess air ratio in the main chamber. On each combination of intake temperature and engine load, a spark sweep and an injected PC fuel mass sweep were performed to obtain the highest indicated efficiency while satisfying the restrictions in terms of combustion stability and knock intensity. It was shown that, unlike in a conventional HCCI engine, the combustion phasing can be directly and reliably controlled by adjusting either spark timing or the reactivity of the pre-chamber mixture, ensuring adequate combustion stability and eliminating potential misfires. A similar indicated efficiency as with conventional HCCI combustion was obtained, while the NOx emissions, although slightly elevated, are still insignificant. Compared to PCSI combustion at the same engine load, a 4-percentage-point increase in indicated efficiency and two times lower NOx emissions were achieved. Compared to the most efficient PCSI operating point, it was 1 percentage point lower, indicating that efficiency was achieved, but the specific NOx emissions are reduced by approximately 70%. Most importantly, very similar performance was obtained with significant variations in intake temperature, proving the reliability and adaptability of this combustion concept.

Improving the efficiency of spark-ignited (SI) engines while simultaneously reducing emissions remains a critical challenge in meeting global energy demands and increasingly stringent environmental regulations. Lean burn combustion is a proven strategy for increasing efficiency in SI engines. However, the air dilution level is limited by the mixture’s ignition ability and poor combustion efficiency and stability. A promising method to extend the dilution limit and ensure stable combustion is the implementation of an active pre-chamber combustion system. The pre-chamber spark-ignited (PCSI) engine facilitates stable and rapid combustion of very lean mixtures in the main chamber by utilizing high ignition energy from multiple flame jets penetrating from the pre-chamber (PC) to the main chamber (MC). Together with the increase in efficiency by dilution of the mixture, nitrogen oxide (NO_X) emissions are lowered. However, at peak efficiencies, the NO_X emissions are still too high and require aftertreatment. The use of exhaust gas recirculation (EGR) as a dilutant might enable simple aftertreatment by using a three-way catalyst. This study experimentally investigates the use of EGR as a dilution method in a PCSI engine fueled by methane and analyzes the benefits and drawbacks compared to the use of air as a dilution method. The experimental results are categorized into three sets: measurements at wide open throttle (WOT) conditions, at a constant engine load of indicated mean effective pressure (IMEP) of 5 bar, and at IMEP = 7 bar, all at a fixed engine speed of 1600 rpm. The experimental results were further enhanced with numerical 1D/0D simulations to obtain parameters such as the residual combustion products and excess air ratio in the pre-chamber, which could not be directly measured during the experimental testing. The findings indicate that air dilution achieves higher indicated efficiency than EGR, at all operating conditions. However, EGR shows an increasing trend in indicated efficiency with the increase in EGR rates but is limited due to misfires. In both dilution approaches, at peak efficiencies, aftertreatment is required for exhaust gases because they are above the legal limit, but a significant decrease in NO_X emissions can be observed.