To meet more and more stringent emission standards, the combined technologies must be used to purify the emission pollutants of vehicle exhaust. Among them, the aftertreatment devices, including DOC, SCR, DPF, and so on, are the most efficient methods. However, after long-term running, the performance of the aftertreatment devices will inevitably degrade. There are several mechanisms that can be used to explain the aging phenomena. For the catalytic devices, such as DOC and SCR, thermal aging and poisoning aging are the most important reasons for their performance deterioration. As for DPF, ash clogging is a key problem for its stable working. To develop and test aftertreatment devices better and faster, the accelerated aging methods must be researched and applied. The small-sample aging method enables accelerated aging of catalyst samples at a very low cost, but its aging accuracy may not be good enough. Although the results of the whole-vehicle aging method and bench engine aging method are more in accord with the real using course, they take too much time and are too expensive to be used widely. Burner aging is a promising way to simulate the long-term running of the catalysts.

In order to understand the driving characteristics of electric heavy-duty trucks in practical application scenarios and promote their usage to replace diesel trucks, this study analyzed the actual usage of electric and diesel heavy-duty trucks in a steel factory based on vehicle-monitoring data and remote online monitoring data and estimated the emission reduction potential of the application of electric trucks by using a mileage-based method and the greenhouse gas emission model. The results showed that the electric heavy-duty trucks in the steel factory mostly operated for over 14 h, with a vehicle kilometers traveled (VKT) of 50–300 km each day, which could meet most of the demands of the transportation of the steel industry. The average daily energy consumption for most trucks falls within the range of 210–230 kWh/100 km, with higher consumption in winter than in summer, which can save approximately 18–26% in operating costs compared with diesel trucks. It is estimated that the usage of these electric heavy-duty trucks can achieve an annual reduction of 115.8 tons of NO_x emissions, 0.7 tons of PM emissions, and 18,000 tons of CO₂ emissions. To further promote the application of electric heavy-duty trucks in China, several policy suggestions, such as introducing priority road-right policies, promoting vehicle and battery leasing markets, and exempting zero-emission vehicles during heavy pollution days, were proposed.

The adoption of new energy vehicles (NEVs) is an effective strategy for pollution reduction, especially for high-emitting commercial vehicles. This paper systematically reviews the promotion policies and development status of zero-emission commercial vehicles (ZECVs) in China, with a focus on diverse application scenarios. Comprehensive policies, including subsidies, right-of-way, infrastructure development, and environmental protection incentives, have significantly advanced NEV adoption, as demonstrated by Shenzhen’s full electrification of buses and the extensive deployment of zero-emission trucks. Despite the overall slow development of ZECVs, regions in southern China and developed areas exhibit better progress. Medium and large passenger vehicles (MLPVs) have achieved a zero-emission rate of around 40%, contrasting with the significantly lower rates of 1.52% for mini and light trucks (MLTs) and 0.44% for medium and heavy trucks (MHTs). Electrification promotion varies significantly in different application scenarios, with buses leading at over 90% zero-emission rates, followed by the airport (24%) and port (16%) vehicles. The electrification of sanitation, logistics, and key industry transport, through lagging, is enhanced by targeted policies and local industry. Buses are designated as the highest priority (Level 1) for electrification transition while intercity logistics and vehicles in key industries are categorized as the lowest priority (Level 4). In addition, policy recommendations, including tailored strategies for ZECV promotion and emission reductions in traditional commercial vehicles, are put forward to provide guidance and reference for setting future zero-emission promotion goals and policy direction for commercial vehicles in subdivided application scenarios.

With increasingly stringent international limits on diesel particulate matter emissions, Continuous-Regeneration Particulate Filters (CRPFs) have been widely applied in heavy-duty vehicle (HDV) exhaust systems. However, their impacts on the complete gaseous pollutant profile remain insufficiently characterized. This study investigated the effects of three CRPF configurations on gaseous emissions from a China III diesel engine under the World Harmonized Transient Cycle (WHTC). Regulated pollutants (CO, total hydrocarbons (THC), NOx, and CO₂) and unregulated pollutants (benzene series compounds and aldehydes) were measured before and after CRPF installation. The results demonstrated that CRPFs achieved high reduction efficiencies for CO (98.5–99.9%) and THC (77.4–99.9%) through catalytic oxidation, while showing negligible effects on NOx (0.2–3.0% reduction) and slight increases in CO₂ (0.07–0.55%). For unregulated pollutants, aldehydes were effectively reduced (formaldehyde: 84.1–100.0%; acetaldehyde: 47.4–100.0%), whereas benzene series compounds exhibited variable responses, with some species showing increased emissions. These findings reveal complex pollutant transformation mechanisms within CRPF systems and provide references for optimizing aftertreatment configurations to meet China VI and subsequent emission standards, thereby contributing to the mitigation of air pollution, the protection of public health, and the promotion of sustainable societal development.