The requirements of 5G/6G promote progress in the miniaturization of the antenna array, which promotes the development of a closely spaced decoupling technique. However, the present techniques face the common problem of beam tilt if the spacing is close. Thus, a pattern-corrected, closely-spaced technique is proposed in this paper for the two patch antennas with the λ₀/20 edge-to-edge distance of the H-plane. The corresponding structure, which is inserted at the center of the spacing, consists of a vertical wall with a single substrate and two symmetrical T-type metals, and a slot at the center is reserved to adequately accommodate the vertical wall. The vertical strip at the other end of the T-type metal is connected to the ground of the patch antenna, while the parallel strip is placed exactly above the patch substrate. After an exact analysis, a prototype was fabricated and measured, and the results showed that the measurements agreed well with those of the simulations, the decoupling coefficients in the 5.8 GHz band were below −20 dB, and the measured radiation pattern at 5.81 GHz was corrected to the broadside from 28° and the maximum realized gain was 5.30 dB.

In order to implement multiple electromagnetic (EM) wave front control, a reconfigurable multifunctional metasurface (RMM) has been investigated in this paper. It can meet the requirements for 6G communication systems. Considering the full-space working modes simultaneously, both reflection and transmission modes, the flexible transmission-reflection-integrated RMM with p-i-n diodes and anisotropic structures is proposed. By introducing a 45°-inclined H-shaped AS and grating-like micro-structure, the polarization conversion of linear to circular polarization (LP-to-CP) is achieved with good angular stability, in the transmission mode from top to bottom. Meanwhile, reflection beam patterns can be tuned by switching four p-i-n diodes to achieve a 1-bit reflection phase, which are embedded in the bottom of unit cells. To demonstrate the multiple reconfigurable abilities of RMMs to regulate EM waves, the RMMs working in polarization conversion mode, transmitted mode, reflected mode, and transmission-reflection-integrated mode are designed and simulated. Furthermore, by encoding two proper reflection sequences with $13\times 13$ elements, reflection beam patterns with two beams and four beams can be achieved, respectively. The simulation results are consistent with the theoretical method. The suggested metasurface is helpful for radar and wireless communications because of its compact size, simple construction, angular stability, and multi-functionality.

MIMO Technology has promoted the developments of various antennas, then the planar antenna will be one of the main directions to satisfy the future compact requirement of the 5G+/6G communications. This chapter introduces different types of the planar antenna and summarizes the implicit compact techniques, where the related techniques like the diversity and the reconfigurable are not included owing to they are the inherent properties of the MIMO antennas. These antennas contain the patch antenna, slot antenna, dipole/monopole antenna, loop antenna, cavity antenna, Yagi-Uda antenna, fractal antenna, UWB antenna, PIFA etc., and their deformations to the specific purposes. On the contrary, the implicit compact techniques are not so explicit as the antenna configurations, but they are classified to be the close-spacing structure without decoupling, owing to the decoupling is not the necessary requirement of MIMO application, decoupling technique of spacing reduction, meandered line technique, multi-element method, co-radiator/co-location design, fractal antenna, and radiator-cutting antenna. Besides, the corresponding techniques for the compact design are also concluded, including the mode-cutting method, fractal technique, characteristic mode analysis, and the optimization algorithms.

For the future application of wireless power transfer on the human body, a wearable directional button antenna, composed of $2\times 3$ artificial magnetic conductor (AMC) cells, is proposed, where the kinetic energy antenna is put on the elbow, which then charges the receiving communication antenna on the upper arm. The radiator of the button antenna is a monopole antenna, which is top-loaded by two cylindrical substrates with different radii to achieve a low profile, and it is fed by the microstrip line made by textiles, including 100% cotton substrate and conductive textile. The AMC cells are put close to the feeding microstrip line in order to realize directional radiation to the other side. Meanwhile, a real human arm model of a Chinese women is built to accurately analyze the corresponding wave propagations. Consequently, two identical antenna prototypes are fabricated, and the corresponding measurements are implemented, where an on-arm approximate measurement method for the radiation pattern is proposed. The measurements agree well with the simulations. Additionally, the influence of the communication antenna on the kinetic energy antenna and the interactions between the antenna and the arm are analyzed. Finally, the transmission efficiency and the SAR values are investigated.