Underwater shock waves generated by pulsed electrical discharges are an effective, economical, and environmentally friendly means of stimulating reservoirs, and this technology has received much attention and intensive research in the past few years. This paper reviews the main results of recent work on underwater electrical wire explosion (UEWE) for reservoir stimulation. A platform is developed for microsecond single-wire explosions in water, and diagnostics based on a voltage probe, current coil, pressure probe, photodiode, and spectrometer are used to characterize the UEWE process and accompanying shock waves. First, the UEWE characteristics under different discharge types are studied and general principles are clarified. Second, the shock-wave generation mechanism is investigated experimentally by interrupting the electrical energy injection into the wire at different stages of the wire-explosion process. It is found that the vaporization process is vital for the formation of shock waves, whereas the energy deposited after voltage collapse has only a limited effect. Furthermore, the relationships between the electrical-circuit and shock-wave parameters are investigated, and an empirical approach is developed for estimating the shock-wave parameters. Third, how the wire material and water state affect the wire-explosion process is studied. To adjust the shock-wave parameters, a promising method concerning energetic material load is proposed and tested. Finally, the fracturing effect of the pulsed-discharge shock waves is discussed, as briefly are some of the difficulties associated with UEWE-based reservoir stimulation.

Electrohydraulic shock waves (ESWs) are widely applied to many fields such as sterilization, lithotripsy, food processing, and so on. Based on high-pulsed power technology, electrical explosion is increasingly utilized to generate shock waves with steep fronts and short duration. In order to further magnify the shock waves, we have proposed a new technique by using energetic materials (EMs) loads. This paper investigated the fracturing effect of the ESWs generated by plasma-ignited EMs explosion. During the ESWs fracturing process, a large-scale triaxial stress pressurizing equipment and a dynamic strain measurement system were applied to the shale samples. The most evident experimental results showed that a large number of cell-shaped multiple cracks developed after the ESWs fracturing process. In addition, interior crack morphology and fluorescent tracing proved the evidence of penetration cracks. These cracks contributed to a great reduction of fracture pressure in fracturing test, which laid a scientific foundation for ESWs technique to be a promising method of well stimulation in those low permeability reservoir and further optimized into a new plugging relief and injection gain technology.

Besides a typical high‐density plasma source, electrical explosion of conductors is also indispensable in switches, nanomaterial synthesis, shock‐wave sources, etc. In this paper, an experimental study regarding plasma dynamics of electrical wire explosions (μs‐timescale) is presented, with spatiotemporal resolved diagnostics. Pure Cu/Ni wire and Cu‐Ni alloy wire were used and compared. The alloy wire usually has a higher resistivity, resulting in a higher initial energy deposition (heating) rate. Abel inverse transformation indicated that the plasma radiation focussed on the outer region of the discharge channel for the alloy wire. In addition, the metallic vapour determined by the material properties had a considerable influence on the plasma process and resulting nanomaterials. In particular, both transverse and axial‐layered structures were observed in alloy wire vapour. In addition, for the first time, the expanding arc‐like plasma of explosion products was understood and examined from aspects of material properties and energy relaxation. The later stage of wire explosion resembled the state of regular metal vapour arcs under 1 MPa pressure. Finally, the core factor for the fast energy deposition stage of wire explosion was ascertained. Correlations between pre‐exposition circuit parameters and post‐explosion dynamic effects were found, which is significant for practical applications.

The large-scale centralized development of wind and PV power resources is the key to China’s dual carbon targets and clean energy transition. The vast desert–Gobi–wilderness areas in northern and western China will be the best choice for renewable energy development under multiple considerations of resources endowment, land use constraints, technical conditions, and economic level. It is urgent to carry out a quantitative wind and PV resource assessment study in desert–Gobi–wilderness areas. This paper proposed a multi-dimensional assessment method considering the influence of the power grid and transportation infrastructure distributions, which includes three research levels, namely, the technical installed capacity, the development potential, and the development cost. Nine main desert–Gobi–wilderness areas were assessed. The wind and PV technical installed capacities were 0.6 TW and 10.7 TW, and the total development potentials were over 0.12 TW and 1.2 TW, with the full load hours of 2513 and 1759 and the average development costs of 0.28 CNY/kWh and 0.20 CNY/kWh. Finally, this paper proposed the meteorological–electrical division distribution. A case study in the Kubuqi and Qaidam Deserts was carried out on wind–wind and wind–PV collaborative development across different meteorological–electrical divisions, which can reduce by 58% the long-term energy storage capacity and decrease the total system LCOE from 0.488 CNY/kWh to 0.445 CNY/kWh.

This paper deals with an experimental study regarding the spatial–temporal evolution of single wire explosions in air and water at atmospheric pressure. Experiments were carried out with a microsecond timescale pulsed current source under 500 J stored energy. The morphology of the exploding wire with different discharge type, wire material, insulating coat, and ambient medium was intensively observed via self-emission images. The results revealed that the plasma radiation of wire explosion in air mainly contained two stages: initial intense radiation from optically thick plasma, and later decaying radiation from expanded arc-like plasma. A hollow structure was observed in a Cu exploding wire in air, and the plasma channel tended to develop inside it. As for W case, there would always be a core-corona structure, resulting in lower expansion rate and shock wave strength. Moreover, the plasma radiation of the underwater wire explosion was mainly determined by two factors: expansion rate and chemical reaction. The expansion rate of the radiant region in water was only 10 ^–1 mm μ s ^–1 level (1 mm μ s ^–1 level for air), leading to the lagging radiation. No noticeable difference in morphology was found between Cu and W wire explosions in water. Particularly, the Al wire explosion generated a bright light emission due to chemical reactions. Finally, radiative characteristics in an exploding wire were preliminarily concluded and existing problems proposed.

This paper proposed and verified a method for adjusting parameters of underwater shock waves. In the experiments, a metal wire with an energetic material coat was exploded by applying a pulsed current on it. Under different matches of size/material of wire, mass/type of energetic material, and injected pulsed current, characteristics of shock waves were obtained. It has been proven that peak pressure, impulse, and energy of shock waves can be conveniently regulated by simply changing the explosion of either the wire or its energetic material coat. Finally, the mechanisms of this method were analyzed and potential applications discussed.