Yahya Bozkurt

Dr. Yahya Bozkurt


Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2021 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
YBYahya Bozkurt
Yahya Bozkurt
EKElif Karayel
Elif Karayel

24 April 2024 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
MKMelike Korgancı
Melike Korgancı
YBYahya Bozkurt
Yahya Bozkurt


14 May 2025 in Progress in Additive Manufacturing
Verified
Journal Article
Closed access
PDF file
YBYahya Bozkurt
Yahya Bozkurt
AAAslıhan Avşar
Aslıhan Avşar
MKMelike Korgancı
Melike Korgancı
Gurel ÇamGurel Çam
Gurel Çam

21 April 2011 in Journal of Composite Materials
Verified
Journal Article
Closed access
PDF file
YBYahya Bozkurt
Yahya Bozkurt
HUHüseyin Uzun
Hüseyin Uzun
SSSerdar Salman
Serdar Salman
The purpose of the study is to present the feasibility of the joining of similar AA2124/SiC/25p–T4 composite plates by friction stir welding (FSW). Microstructure properties, microhardness, and tensile tests have been performed to evaluate the weld zone characteristics and the performance of AA2124/SiC/25p–T4 composite joints. The phase structure of a similar AA2124/SiC/25p–T4 composite weld was determined from X-ray diffraction (XRD). The temperature in the weld zone have been evaluated using thermocouples in order to demonstrate the FSWed joint of the AA2124/SiC/25p–T4 composite without melting. The obtained results revealed that FSW can be used in the joining of similar AA2124/SiC/25p–T4 composite plates. XRD measurements show that SiO2 phase was detected in the weld zones. It was determined that the peak temperatures achieved at 15 mm away from the weld center varied between 201°C and 270°C. In addition, the tensile strength of AA2124/SiC/25p–T4 butt joints was found to be approximately 20% lower than that of the base composite. The originality of this study is one of the preliminary studies on the detailed examination of the microstructural and mechanical properties of the AA2124/SiC/25p–T4 composite joint by FSW.

26 August 2011 in Scientific Research and Essays
Verified
Journal Article
Open access
PDF file
YBYahya Bozkurt
Yahya Bozkurt
DSDuman Serdal
Duman Serdal
Assemblies consisting of aluminum and particle reinforced aluminum composite alloys have wide spread applications in construction and automotive industries. For a successful use of such dissimilar joints, the welds must have sufficient strength and formability. In the present study, 3003-H24 aluminum alloy and 2124/SiC/25p-T4 composite plates were successfully friction stir butt joined by offsetting the high strength plate to retreating side of the tool under tool rotational speed of 900 to 1400 rpm and traversing speed of 40 to 125 mm/min, keeping other parameters constant. Ultimate tensile strength, percentage elongation and joint efficiency values of the welded joints and hardness variations across the weld interface were determined. The integrity of the joints was investigated using optical microscopy, scanning electron microscopy and energy dispersive spectroscopy. Results indicated that the high quality welded joints could be obtained when a tool rotational speed of 900 rpm and a traverse speed of 125 mm/min were employed. The maximum tensile strength value obtained was about 182 MPa, which corresponds to a joint efficiency of 104% of that of the aluminum alloy base metal. Key words: Friction stir welding, dissimilar joint, microhardness, mechanical properties.