A hydraulic drive-based self-propelled photovoltaic panel cleaning robot was developed to tackle the challenges of harsh environmental conditions, difficult roads, and incomplete cleaning of dust particles on the photovoltaic panel surface in photovoltaic power plants. The robot has the characteristics of the crawler wheel drive, rear-wheel-independent turning and three-point-independent suspension design, which makes it adhere to the walking requirements of complex environmental terrains, more flexible in turning and automatically levelling so that the stability of the boom mechanism during walking can be ensured. The kinematics model of the upper arm structure equipped with the end cleaning device was built, and the optimized Circle chaotic map and nonlinear weight factor were introduced to enhance the search ability and convergence speed of the sparrow algorithm. Furthermore, the boom running track was optimized in combination with the seven-order non-uniform B-spline curve. Through optimization, the running time of the boom was reduced by 18.7%, and the cleaning efficiency of photovoltaic panel surface was increased. The effectiveness of self-propelled photovoltaic panel cleaning robot cleaning and the reliability of time-optimal trajectory planning were confirmed through simulation and experiment.

Three-wheeled agricultural robots possess the advantages of high flexibility, strong maneuverability, and low cost. They can adapt to various complex terrains and operational environments, making them highly valuable in the fields of crop planting, harvesting, irrigation, and more. However, the horizontal stability of the three-wheeled agricultural robot chassis is compromised when working in harsh terrain, significantly impacting the overall operational quality and safety. To address this issue, this study designed a leveling system based on active suspension and proposed a stepwise leveling method based on an adaptive dual-loop composite control strategy (ADLCCS-SLM). Firstly, in the overall control of the three-wheeled chassis, a stepwise leveling method (SLM) was introduced. This method allows for rapid leveling by incrementally adjusting one or two suspensions, effectively avoiding the complex interactions between suspension components encountered in traditional methods involving the simultaneous linkage of three suspensions. Next, in terms of suspension actuator control, an adaptive dual-loop composite control strategy (ADLCCS) was proposed. This strategy employs a dual-loop composite control both internally and externally and utilizes an improved adaptive genetic algorithm to adjust critical control parameters. This adaptation optimizes the chassis leveling performance across various road conditions. Finally, the effectiveness of the proposed ADLCCS-SLM was validated through simulation and experimental testing. The test results showed that the control effect of the proposed method was significant. Compared to the traditional multi-suspension linkage leveling method based on PID, the peak values of pitch angle and roll angle were reduced by 31.8% and 33.3%, respectively.

In this study, to address the issues of tooth tip operation discontinuity and jitter during autonomous excavator operation, a multi-segment mixed interpolation method utilizing different higher-order polynomials has been proposed. This approach is designed to optimize the tooth tip trajectory of the excavator under multiple constraints, resulting in a smoother trajectory. Specifically, the single-bucket excavator was chosen as the research object, and three different high-order mixed polynomials were utilized to interpolate the trajectory of the digging discrete points. Through a comparative analysis under multiple constraints, this study explored and analyzed the joint angle, angular velocity, and angular acceleration curves of each excavator’s joint. An experimental platform was established to investigate the hydraulic system of an excavator, and the optimal trajectory was controlled using a high-order mixed polynomial interpolation. The results of this study demonstrate that the tracking accuracy of the excavator’s actuator under the optimal interpolation strategy is high, with a maximum displacement deviation of ±3 mm. Additionally, during operation, the excavator manipulator runs smoothly and continuously with minimal flexible impact and vibration.

The independent metering system used in the combination of traditional cartridge proportional valves employs an excessive number of components, which increases the complexity of the control strategy. To address this problem, a novel independent metering system based on pilot hydraulic control was developed. Following the pressure and flow requirements, the structure and valve body size of the two spools were designed. The effect of the parameter change in the control valve on the dynamic response characteristics of the main spool was investigated by simulation. A control strategy was developed based on load force direction prediction and two-chamber pressure switching to verify the feasibility of working mode switching during load direction change. As indicated by the results, compared with the mode switching control strategy of the traditional independent metering system, the proposed control strategy could effectively reduce the number of mode switching and ensure the continuity of the actuator operation. Compared with the traditional load-sensitive valve control system, the proposed pilot-controlled independent metering system achieved an average energy-saving efficiency of 47.27%. This study provides technical reference for the low energy consumption, high efficiency, and sustainable development of hydraulic systems.