Based on the concept of component assembly, a novel star polygon-coupled honeycomb metamaterial, which achieves a collaborative improvement in load-bearing capacity and vibration suppression performance, is proposed based on a common polygonal structure. The compression simulation and experiment results show that the load-bearing capacity of the proposed metamaterial is three times more than that of the initial metamaterial. Additionally, metal pins are attached and particle damping is applied to the metamaterial to regulate its bandgap properties; the influence of configuration parameters, including the size, number, position, and material of the metal pins, on bandgaps is also investigated. The results show that the bandgap of the proposed metamaterial can be conveniently and effectively regulated by adjusting the parameters and can effectively suppress vibrations in the corresponding frequency band. Particle damping can be used to continuously adjust the frequency of the bandgap and further enhance the vibration suppression capacity of the metamaterial in other frequency bands. This paper provides a reference for the design and optimization of metamaterials.

This study aimed to investigate the metallographic structure and the impact of the heat treatment process on the MAR-M247 superalloy, a high-temperature nickel-based superalloy commonly used in turbine blades. The heat treatment process can potentially influence the mechanical properties of the MAR-M247 superalloy at different temperatures. A strength simulation analysis of gas turbine blades should include the variations in the mechanical properties of the material. The effect of heat treatment on grain size was investigated by metallographic experiments, and numerical calculations of material mechanical properties were conducted. The mechanical property parameters necessary for finite element analysis of turbine blades were determined. Finally, a finite element simulation model of the blade was established based on these mechanical property parameters, and strength analysis was performed. The simulation results provided the stress distribution and the strength of the turbine blade.

High-speed direct-drive permanent magnet synchronous motors (PMSMs), supported by elastic foil gas bearings, have broad applications, such as in microcompressors. However, some problems remain to be solved for the electrical performance analysis of PMSMs. For example, there is presently no related analytical model that can be used in rotor dynamics expression for this type of PMSM. This study aimed to establish theoretical models for electromagnetic force density and torque. The process involved both theoretical and experimental research. The analytic models of air gap magnetic density, electromagnetic force density, and electromagnetic performance were established for a PMSM with a parallel magnetized cylindrical permanent magnet. The analytic calculation was conducted, and the results of the analytic model were obtained. The analytical model of the electromagnetic torque and force can be applied in theoretical research on rotor dynamics. The model provides a theoretical basis and method for studying the influence of the electromagnetic load on rotor dynamics. A finite element simulation analysis of the electrical performance of the PMSM was carried out. An electrical performance experiment was conducted. The deviation between the experimental result and the theoretical value was less than 4%. This result indicated that the analytic models could be used in a dynamics analysis of compressors that are directly driven by a PMSM for application in engineering and industrial contexts.

With the development of urban rail transportation, the environmental vibration problem caused by the running of metro vehicles has received attention. In order to reduce ground vibration near buildings caused by metro vehicles running on viaducts, this paper establishes the train–track–viaduct rigid–flexible coupling dynamics model and pier–soil–building finite element model and carries out the simulation calculation and analysis of ground vibration. The influence of train speed and fastener stiffness on ground vibration is explored, and the vibration reduction effect of the track vibration reduction pad and continuous support vibration reduction structure is studied. The results show that the ground vibration near the building caused by the train running on the viaduct decreases with the reduction in speed, when the speed is reduced to 40 km/h, the vibration attenuation is slower as the speed continues to be reduced; the reduction in the vertical stiffness of fasteners can reduce ground vibration; the arrangement of the vibration damping pad can effectively reduce ground vibration, and after installing a vibration damping pad, 0–23 Hz and 50–80 Hz ground vibration speeds are effectively suppressed. In order to meet the environmental requirements for ground vibration, the vehicle speed can be reduced to less than 35 km/h or vibration damping mats can be installed.

Tire acoustic cavity resonance noise (TACRN) contributes significantly to the interior noise of electric cars and passenger cars with lower powertrain noise, which affects the comfort of the ride. To suppress TACRN effectively, it is crucial to clarify the characteristics of TACRN. In previous studies, the acoustic wave in the tire acoustic cavity is straightforwardly assumed to be the plane wave for convenience. In fact, there exist strict conditions for the acoustic wave propagating in the pipeline to act as a plane wave. The aim of this paper is to make the characteristics and evolution of acoustic waves in tire acoustic cavities clear. To do so, a simplified model of the tire cavity is established, and the sound field distribution and the acoustic wave propagation characteristics in the tire cavity are analyzed based on the theory of acoustic waveguide. Then, the existence ranges of higher-order waves (non-plane waves), the conditions of an acoustic wave evolving into a plane wave, and the frequency range of a plane wave are investigated. Finally, the characteristics and evolution law of an acoustic wave in a tire acoustic cavity are obtained. The work in this paper may deepen the understanding of the characteristics and mechanism of acoustic waves in the tire cavity and be helpful and meaningful for analyzing and suppressing TACRN. Therefore, it is of practical significance to reduce TACRN transmitted to the vehicle and improve the sound quality inside the vehicle.

With the increasing speed of high-speed train, it is more and more difficult to reduce the vibration and noise inside the train. The floor of the train, as a carriage component in direct contact with passengers, is of great significance to improve its vibration and sound isolation performance to ensure the comfort of passengers. In this article, a floor vibration isolator with quasi-zero stiffness is designed based on the dimensional parameters of the traditional floor vibration isolator, and the vibration isolation performance is analyzed by the finite element model of the floor vibration isolator from the static and dynamics aspects, respectively. The load-displacement curves of the floor vibration isolator are obtained through static simulation calculations, and the dynamic analysis of the floor vibration isolator is carried out by simulation methods, which verifies the low-frequency vibration isolation performance of the floor vibration isolator under different working conditions, and the vibration isolator has a good prospect for development.