Norasyikin Bte Ismail

Dr. Norasyikin Bte Ismail

orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 2020 in Fuel
Verified
Journal Article
Closed access
NINorasyikin Bte Ismail
Norasyikin Bte Ismail
BHBerna Hascakir
Berna Hascakir

1 October 2018 in Journal of Petroleum Science and Engineering
Verified
Journal Article
Closed access
NINorasyikin Bte Ismail
Norasyikin Bte Ismail
ESE. Seber
E. Seber
BHB. Hascakir
B. Hascakir

7 June 2016
Verified
Conference Paper
Closed access
NINorasyikin Bte Ismail
Norasyikin Bte Ismail
KKKristina A. Klock
Kristina A. Klock
BHBerna Hascakir
Berna Hascakir
In-situ Combustion (ISC) has the potential to be the most effective enhanced oil recovery (EOR) method for heavy oil recovery. However, it is considered a high risk failure rate process since it is hard to predict the combustion reactions between complex crude oil and heterogeneous rock matrices. If the reservoir rock is reactive, like carbonates, the risk factor of ISC increases. This research studies the ISC performance for different rock matrices found in Alberta, Canada. The reaction kinetics analyses were carried out by Thermogravimetric Analysis/Differential Scanning Calorimetry (TGA/DSC) on bulk oil, and its Saturates, Aromatics, Resins, and Asphaltenes (SARA) fractions at a constant heating rate (20°C/min). To better understand the combustion behavior of bulk oil, pseudo blends of SARA fractions were prepared and systematic TGA/DSC tests were run on these blends. Furthermore, the impact of reactive porous media on fuel formation mechanism was investigated by using clays and carbonates. The reaction kinetic analyses on bulk oil and SARA fractions suggest that asphaltenes, resins, and aromatics fractions go into endothermic reactions at elevated temperatures, still the asphaltenes fraction generates the greatest amount of heat. The two-component interaction of asphaltenes with other fractions produces less heat than the combustion of asphaltenes alone. The three- component pseudo blend prepared by mixing asphaltenes-resins-aromatics produced the highest amount of heat and we believe that in bulk oil combustion saturates by acting as an ignitor provides the necessary heat to initiate the reactions among aromatics, resins, and asphaltenes fractions. Moreover, the effect of reactive porous media on reaction kinetics of bulk oil were investigated at a constant heating rate (20°C/min). Carbonates and clays were used. Since the clays act like a catalyst, heat generation was observed lower with clays than carbonates and carbonates required more heat for successful combustion. While the heating rates during in-situ combustion are generated naturally, in TGA/DSC tests, a constant heating rate is applied. In this study, we used 20°C/min as the heating rate. If the same heating rate during ISC cannot be reached, then, the heat generation cannot be as high as reported in this manuscript. Thus, it is important to extend the systematic TGA/DSC analyses presented in this paper. Tests should be conducted at varying heating rates on different oil samples and on their SARA fractions.

26 August 2021 in International Journal of Engineering Technology and Sciences
Verified
Journal Article
Open access
PDF file
OTOfellia Thong
Ofellia Thong
AIAmirah Ibrahim
Amirah Ibrahim
HRHussien Abdul Rahim
Hussien Abdul Rahim
WYWeng Jun Yong
Weng Jun Yong
NINorasyikin Bte Ismail
Norasyikin Bte Ismail
The development of petrochemical refinery industries has resulted in increased production of petroleum sludge and its disposal, which poses a risk of introducing hazardous elements into the environment. Eliminating petroleum sludge from storage, processing, transportation, and pipeline systems were always a major problem for the oil and gas industry. Today there are an estimated 60 million tons of petroleum sludge produced annually. Statistics also show that one ton of oily sludge is produced for every 500 tons of crude oil processed. Therefore, the petroleum industry requires protected and environmentally friendly techniques to find alternative treatment methods for petroleum sludge. Among the possible methods, oil recovery using solvent extraction method has been widely used for petroleum sludge treatment under different experimental factors. The reason is because solvent extraction is one of the cheapest and most efficient recycling processes. In addition, it used lubricating oil that does not require water, and the solvent is reusable. However, solvent extraction alone is insufficient for extracting crude oil from a large volume of petroleum sludge due to low efficiency and high variability. Therefore, combining different methods of solvent extraction and freeze-thaw hybrid technique may improve the oil extraction efficiency. Thus, this paper reviews thorough analysis of petroleum sludge’s physical and chemical properties and its oil recovery using solvent extraction and freeze-thaw method to promote the waste-to-wealth initiative.

18 October 2023 in Materials Today: Proceedings
Verified
Journal Article
Closed access
NKNur Aqilah Kamaludin
Nur Aqilah Kamaludin
NSNur Najwa Syuhada Suhaidi
Nur Najwa Syuhada Suhaidi
NINorasyikin Bte Ismail
Norasyikin Bte Ismail

1 March 2026 in Petroleum Research
Verified
Journal Article
Open access
BMBarima Money
Barima Money
RMRayan Hassan Modather
Rayan Hassan Modather
DADavid Abutu
David Abutu
NINorasyikin Bte Ismail
Norasyikin Bte Ismail
AAAugustine Agi
Augustine Agi
SMSiti Qurratu' Aini Mahat
Siti Qurratu' Aini Mahat