In this work, a novel composite of bacterial cellulose (BC) and expanded vermiculite (EVMT) composite was used to adsorb dyes and antibiotics. The pure BC and BC/EVMT composite were characterized using SEM, FTIR, XRD, XPS and TGA. The BC/EVMT composite exhibited a microporous structure, providing abundant adsorption sites for target pollutants. The adsorption performance of the BC/EVMT composite was investigated for the removal of methylene blue (MB) and sulfanilamide (SA) from an aqueous solution. The adsorption capacity of BC/ENVMT for MB increased with increasing pH, while the adsorption capacity for SA decreased with increasing pH. The equilibrium data were analyzed using the Langmuir and Freundlich isotherms. As a result, the adsorption of MB and SA by the BC/EVMT composite was found to follow the Langmuir isotherm well, indicating a monolayer adsorption process on a homogeneous surface. The maximum adsorption capacity of the BC/EVMT composite was found to be 92.16 mg/g for MB and 71.53 mg/g for SA, respectively. The adsorption kinetics of both MB and SA on the BC/EVMT composite showed significant characteristics of a pseudo-second-order model. Considering the low cost and high efficiency of BC/EVMT, it is expected to be a promising adsorbent for the removal of dyes and antibiotics from wastewater. Thus, it can serve as a valuable tool in sewage treatment to improve water quality and reduce environmental pollution.
The LiCuxMn1.95−xSi0.05O4 (x = 0, 0.02, 0.05, 0.08) samples have been obtained by a simple solid-state method. XRD and SEM characterization results indicate that the Cu-Si co-doped spinels retain the inherent structure of LiMn2O4 and possess uniform particle size distribution. Electrochemical tests show that the optimal Cu-doping amount produces an obvious improvement effect on the cycling stability of LiMn1.95Si0.05O4. When cycled at 0.5 C, the optimal LiCu0.05Mn1.90Si0.05O4 sample exhibits an initial capacity of 127.3 mAh g−1 with excellent retention of 95.7% after 200 cycles. Moreover, when the cycling rate climbs to 10 C, the LiCu0.05Mn1.90Si0.05O4 sample exhibits 82.3 mAh g−1 with satisfactory cycling performance. In particular, when cycled at 55 °C, this co-doped sample can show an outstanding retention of 94.0% after 100 cycles, whiles the LiMn1.95Si0.05O4 only exhibits low retention of 79.1%. Such impressive performance shows that the addition of copper ions in the Si-doped spinel effectively remedy the shortcomings of the single Si-doping strategy and the Cu-Si co-doped spinel can show excellent cycling stability.
In this work, LiMn2−xErxO4 (x ≤ 0.05) samples were obtained by sol-gel processing with erbium nitrate as the erbium source. XRD measurements showed that the Er-doping had no substantial impact on the crystalline structure of the sample. The optimal LiMn1.97Er0.03O4 sample exhibited an intrinsic spinel structure and a narrow particle size distribution. The introduction of Er3+ ions reduced the content of Mn3+ ions, which seemed to efficiently suppress the Jahn–Teller distortion. Moreover, the decreased lattice parameters suggested that a more stable spinel structure was obtained, because the Er3+ ions in a ErO6 octahedra have stronger bonding energy (615 kJ/mol) than that of the Mn3+ ions in a MnO6 octahedra (402 kJ/mol). The present results suggest that the excellent cycling life of the optimal LiMn1.97Er0.03O4 sample is because of the inhibition of the Jahn-Teller distortion and the improvement of the structural stability. When cycled at 0.5 C, the optimal LiMn1.97Er0.03O4 sample exhibited a high initial capacity of 130.2 mAh g−1 with an excellent retention of 95.2% after 100 cycles. More significantly, this sample showed 83.1 mAh g−1 at 10 C, while the undoped sample showed a much lower capacity. Additionally, when cycled at 55 °C, a satisfactory retention of 91.4% could be achieved at 0.5 C after 100 cycles with a first reversible capacity of 130.1 mAh g−1.
Any solid surface with homogenous or varying surface energy can spontaneously show variable wettability to liquid droplets with different or identical surface tensions. Here, we studied a glass slide sprayed with a quasi-superamphiphobic coating consisting of a hexane suspension of perfluorosilane-coated nanoparticles. Four areas on the glass slide with a total length of 7.5 cm were precisely tuned via ultraviolet (UV) irradiation, and droplets with surface tensions of 72.1–33.9 mN m−1 were categorized at a tilting angle of 3°. Then, we fabricated a U-shaped device sprayed with the same coating and used it to sort the droplets more finely by rolling them in the guide groove of the device to measure their total rolling time and distance. We found a correlation between ethanol content/surface tension and rolling time/distance, so we used the same device to estimate the alcoholic strength of Chinese liquors and to predict the surface tension of ethanol aqueous solutions.