In this article, a novel machine learning regression-based single-event transient (SET) modeling method is proposed. The proposed method can obtain a reasonable and accurate SET model without introducing complex physical mechanisms, which are not suitable for circuit-level simulation, into the model. To capture the essential physics behind these current transients caused by SET in the circuit-level simulations, we collect plenty of SET current data under different conditions [e.g., different linear energy transfer (LET), different drain bias voltage, different strike position, etc.] to train the SET model. To show the effectiveness of the proposed modeling method, we build a SET pulse current model by learning SET current data of Semiconductor Manufacturing International Corporation (SMIC) 130-nm bulk CMOS obtained by TCAD simulation. A multilayer feedforward neural network is used to build the SET pulse current model and the built SET model takes into account the dependence of time, LETs, drain bias voltages, and strike positions. The results from the model are validated with the simulation from TCAD. The trained SET pulse current model is implemented as a Verilog-A current source in the Cadence Specter circuit simulator, and an inverter with five fan-outs is used to show the practicability and reasonableness of the proposed SET pulse current model for circuit-level single-event effect (SEE) simulation.
4 January 2022 in IEEE Transactions on Electron Devices
High-voltage p-i-n diodes for space applications are sensitive to single event burnout (SEB), which may cause the failure of the entire electronic system. This article describes the SEB failure mechanism of high-voltage p-i-n diodes with field limiting rings (FLRs) termination structure, based on the electro-thermal coupled transient simulation model in the Sentaurus TCAD simulator. The simulation results show that the catastrophic failures result from the intense local heating at the edge of the main junction, because the high electric field strength at this region induces strong impact ionization of the charge carriers. The strike at the edge of the main junction shows the strongest sensitivity to SEB since the energetic particle-induced carriers are deposited exactly at the high electric field region. Then, a novel SEB hardening technique of localized carrier lifetime control at the edge of the main junction region is proposed based on the analysis on the failure mechanism. Our simulation results demonstrate that the reduction of the localized carrier lifetime can alleviate the peak electric field and reduce the local heat accumulation, thereby improving the SEB performance of high-voltage p-i-n diodes.
20 July 2022 in IEEE Transactions on Electron Devices
This article presents the coupled electrothermal simulation results of single event burnout (SEB) in power diode with field limiting rings termination structure. Two different hardening techniques of low carrier lifetime control and introducing the buffer layer are investigated comparatively in both the radiation tolerance improvement and the electrical performance degradation. Our simulations reveal that a significant reduction in the carrier lifetime is needed for the hardening of the power diode using only the carrier lifetime control method. However, the sharp increases in the forward voltage drop and the leakage current at the lower carrier lifetime make this hardening technique unacceptable. On the contrary, the addition of the buffer layer is able to improve the safe operating area under the heavy ion irradiation even up to the breakdown voltage, while the breakdown characteristics and the leakage current are kept unchanged and the increases in the forward voltage drop and the reverse recovery charge can be well controlled. In conclusion, adding a buffer layer is considered a superior and promising hardening technique.
Power MOSFETs are found to be very vulnerable to single-event burnout (SEB) in space irradiation environments, and the military components generally require that devices could operate reliably as the temperature varies from 218 K to 423 K (−55 °C to 150 °C); thus, the temperature dependence of single-event burnout (SEB) in power MOSFETs should be investigated. Our simulation results showed that the Si power MOSFETs are more tolerant to SEB at a higher temperature at the lower LET (10 MeV∙cm2/mg) due to the decrease of the impact ionization rate, which is in good agreement with the previous research. However, the state of the parasitic BJT plays a primary role in the SEB failure mechanism when the LET value is greater than 40 MeV∙cm2/mg, which exhibits a completely different temperature dependence from that of 10 MeV∙cm2/mg. Results indicate that with the temperature increasing, the lower difficulty to turn on the parasitic BJT and the increasing current gain all make it easier to build up the regenerative feedback process responsible for SEB failure. As a result, the SEB susceptibility of power MOSFETs increases as ambient temperature increases when the LET value is greater than 40 MeV∙cm2/mg.
With the continuous progress in integrated circuit technology, single-event effect (SEE) has become a key factor affecting the reliability of aerospace integrated circuits. Simulating fault injection using the computer simulation technique effectively reflects the SEE in aerospace integrated circuits. Due to various masking effects, only a small number of faults will result in errors; the traditional method of injecting one fault in one workload execution is inefficient. The method of injecting multiple faults in one workload execution will make it impossible to judge which fault results in errors because the propagation characteristic of SEE and faults may affect each other. This paper proposes an improved multi-point fault injection method to improve simulation efficiency and solve the problems of the general multi-point fault injection method. If one workload execution does not result in errors, multiple faults can be verified by one workload execution. If one workload execution results in errors, a specific grouping method can be used to determine which faults result in errors. The experimental results show that the proposed method achieves a good acceleration effect and significantly improves the simulation efficiency.