The performances of a photovoltaic panel (PV) are defined according to the “peak power” that identifies the maximum electric power supplied by the panel when it receives an insolation of 1kW/m2 and the temperature of the cell is maintained at 25°C. These conditions are only nominal since the solar radiation has a variable intensity and also the panel is subjected to thermal excursions; due to these reasons the real power efficiency of the panel is considerably lower than that obtainable in the nominal conditions.The study focused on assessing a method to reduce the peak temperatures of PV systems using Phase Change Materials (PCM). To this aim it was created a numerical model capable to describe the behaviour of a PV-PCM systems. The results were validated and compared with real data obtained from a test facility

The correlation between water and energy is currently the focus of several investigations. In particular, desalination is a technological process characterized by high energy consumption; nevertheless, desalination represents the only practicable solution in several areas, where the availability of fresh water is limited but brackish water or seawater are present. These natural resources (energy and water) are essential for each other; energy system conversion needs water, and electrical energy is necessary for water treatment or transport. Several interesting aspects include the study of saline desalination as an answer to freshwater needs and the application of renewable energy (RE) devices to satisfy electrical energy requirement for the desalination process. A merge between renewable energy and desalination is beneficial in that it is a sustainable and challenging option for the future. This work investigates the possibility of using renewable energy sources to supply the desalination process. In particular, as a case study, we analyze the application of wave energy sources in the Sicilian context.

Hydrogen produced by renewable sources represents an interesting way to reduce the energetic dependence on fossil fuels in the transportation sector. This paper shows a feasibility study for the production, storage and distribution of hydrogen in the western Sicilian context, using three different renewable sources: wind, biomass and sea wave. The objective of this study is the evaluation of the hydrogen demand, needed to replace all diesel supplied buses with electrical buses equipped with fuel cells. An economic analysis is presented with the evaluation of the avoidable greenhouse gas emissions. Four different scenarios correlate the hydrogen demand for urban transport to the renewable energy resources present in the territories and to the modern technologies available for the production of hydrogen. The study focuses on the possibility of tapping into the potential of renewable energies (wind, biomass and sea wave) for the production of hydrogen by electrolysis. The use of hydrogen would reduce significantly the emissions of particulate and greenhouse gases in the urban districts under analysis.

The main purpose of this paper is to analyze the energy production in the Maltese islands, focusing on the employment of renewable energies in order to increase their energy independence. The main renewable source here proposed is wave energy: thanks to a strategic position, Malta will be able to produce electrical energy using an innovative type of Wave Energy Converter (WEC) based on the prototype of a linear generator realized by University of Palermo. The use of this new technology will be able to cut down the electrical energy production from traditional power plants and, consequently, the greenhouse gas emissions (GHG). Wave energy source and off-shore photovoltaic (PV) technology are here proposed. Particularly, the installation of 12 wave farms, for a total installed capacity of 86 MW, will generate about 9.5% of Malta’s energy requirement in 2025, while the installation of 9.6 MW of off-shore PV will generate about 0.73%.

The reduction of electrical energy consumption in buildings is a subject of great interest in the international scientific community. In buildings with a lot of available natural light, designed with large glazed surfaces, the artificial lighting system is often oversized and cannot be divided into segments to meet lighting demands during daylight hours.This article presents an experimental study, conducted in a university lecture hall that has a glazed surface covering the whole wall at one end, which provides a level of internal illumination that is only sufficient for the area next to the window itself, even when the outside lighting conditions are very bright. It is therefore necessary to turn on the artificial lighting system.The mathematical approach used in this paper has been successfully applied by the authors in other fields of science [1-2].Using an automatic dimmer system, the calibration of which is based on experimental measurements, the lighting is arranged in such a way as to illuminate the most disadvantaged areas of the room, and then to extend itself gradually to the whole of the room, over the period of time that the lecture hall is in use.