TAHAR ABBES Miloud

Prof. Dr. TAHAR ABBES Miloud

Mechanical engineering, University Hassiba Benbouali of Chlef, Chlef, Algeria
+1

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 July 2021 in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
Verified
Journal Article
Open access
PDF file
SBSaliha MOHAMMED BELKEBIR
Saliha MOHAMMED BELKEBIR
BKBenyoucef Khelidj
Benyoucef Khelidj
TMTAHAR ABBES Miloud
TAHAR ABBES Miloud
In order to investigate a viable approach to achieving high efficiencies and low nitrogen oxide (NOX) emissions, this paper presents the application of a homogeneous charge compression ignition (HCCI) engine and the partially premixed combustion (PPC) mode applied to a heavy diesel engine. The effect of carbon dioxide (CO2) fraction on combustion parameters was analyzed and discussed in detail. For this purpose, on the one hand, ANSYS CHEMKIN-Pro software was used to perform simulations of a closed homogeneous reactor under conditions relevant to HCCI engines, and on the other hand, ANSYS-Fluent software was used by adding a CO2 fraction varying from 20% to 58% to methane fuel to study 2D flow simulation by applying a PPC combustion mode to predict the distribution of various output parameters such as in-cylinder temperature, in-cylinder pressure and emissions. In comparison with the two presented models, it was found that the HCCI engine showed a lower NOX level than the PPC mode and this was due to the lower in-cylinder temperature in the HCCI engine.

19 October 2023 in Journal of Renewable Energies
Verified
Journal Article
Open access
PDF file
FBFatih Bouzeffour
Fatih Bouzeffour
BKBenyoucef Khelidj
Benyoucef Khelidj
MAMohamed Abbas
Mohamed Abbas
TMTAHAR ABBES Miloud
TAHAR ABBES Miloud
Dans cet article, on propose une étude théorique sur les transferts de chaleur dans un générateur-adsorbeur contenant le couple charbon actif- méthanol. L’étude porte sur une comparaison de l’évolution de la température à l’intérieur des deux conceptions sous forme tubulaire et rectangulaire par une simulation numérique de l’équation de la chaleur par conduction. La résolution de cette équation par la méthode des différences finies monodimensionnelle avec l’utilisation de Matlab nous a permis de déterminer le champ des températures dans le milieu poreux. Les résultats numériques obtenus montrent un gradient de températures plus important au long de l’épaisseur de charbon actif.

1 December 2025 in Tribology in Industry
Verified
Journal Article
Closed access
MBMohamed Benbrik
Mohamed Benbrik
MBMohamed Bouzit
Mohamed Bouzit
TMTAHAR ABBES Miloud
TAHAR ABBES Miloud
PMPatrick Maspeyrot
Patrick Maspeyrot
The piston-cylinder is the main component of the transmission of energy in the vehicle's engine, but it represents a significant source of unavoidable friction, which negatively affects engine performance by reducing piston lifespan and increasing fuel consumption. To determine the effect of lubrication performance and asperity contact on the tribological characteristics, mainly on the friction generated by asperity sliding contact, a numerical model of a real piston cylinder operating in mixed lubrication was developed. The mixed lubrication analysis shows the necessity to take into account the elasticity of the piston skirt-cylinder as well as for cavitation to ensure the consistency of the results. The sliding friction, resulting from the Johnson contact model, is developed, with a new approach, according to the Bowden-Tabor friction model. An experimental method is employed to determine the coefficient of the sliding friction. The results show that the tribological characteristics—contact pressure, sliding contact friction, energy loss, and the coefficient of sliding contact friction—are influenced by the waviness of the contact surface. When the amplitude of the asperities increases from 12 to 16 µm, the coefficient of the sliding friction and the corresponding contact energy loss increase from 0.128 to 0.16 and from 0.054 J to 1.126 J, respectively, representing 25% to 78% of the total energy loss.