ENESI ASIZEHI YAHAYA

Mr. ENESI ASIZEHI YAHAYA


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 October 2021 in International Journal of Robotics and Control Systems
Verified
Journal Article
Open access
PDF file
OTOmokhafe J. Tola
Omokhafe J. Tola
EUEdwin A. Umoh
Edwin A. Umoh
EYENESI ASIZEHI YAHAYA
ENESI ASIZEHI YAHAYA
In recent times, intense research has been focused on the performance enhancement of permanent magnet synchronous motors (PMSM) for electric vehicle (EV) applications to reduce their torque and current ripples. Permanent magnet synchronous motors are widely used in electric vehicle systems due to their high efficiency and high torque density. To have a good dynamic and transient response, an appropriate inverter topology is required. In this paper, a five-level inverter fed PMSM for electric vehicle applications, realized via co-simulation in an electromagnetic suite environment with a reduced stator winding current of PMSM via the use of in-phase disposition (PD) pulse width modulation (PWM) techniques as the control strategy is presented. The proposed topology minimizes the total harmonic distortion (THD) in the inverter circuit and the motor fed and also improves the torque ripples and the steady-state flux when compared to conventional PWM techniques. A good dynamic response was achieved with less than 10A stator winding current, zero percent overshoot, and 0.02 second settling time synchronization. Thus, the stator currents are relatively low when compared to the conventional PWM. This topology contribution to the open problem of evolving strategies that can enhance the performance of electric drive systems used in unmanned aerial vehicles (UAV), mechatronics, and robotic systems.

5 March 2022 in International Journal of Robotics and Control Systems
Verified
Journal Article
Open access
PDF file
OTOmokhafe James Tola
Omokhafe James Tola
EUEdwin A. Umoh
Edwin A. Umoh
EYENESI ASIZEHI YAHAYA
ENESI ASIZEHI YAHAYA
OOOsinowo E. Olusegun
Osinowo E. Olusegun
Wind power generation has recently received a lot of attention in terms of generating electricity, and it has emerged as one of the most important sources of alternative energy. Maximum power generation from a wind energy conversion system (WECS) necessitates accurate estimation of aerodynamic torque and system uncertainties. Regulating the wind energy conversion system (WECS) under varying wind speeds and improving the quality of electrical power delivered to the grid has become a difficult issue in recent years. A permanent magnet synchronous generator (PMSG) is used in the grid-connected wind-turbine system under investigation, followed by back-to-back bidirectional converters. The machine-side converter (MSC) controls the PMSG speed, while the grid-side converter (GSC) controls the DC bus voltage and maintains the unity power factor. The control approach is second-order sliding mode controls, which are used to regulate a nonlinear wind energy conversion system while reducing chattering, which causes mechanical wear when using first-order sliding mode controls. The sliding mode control is created using the modified super-twisting method. Both the power and control components are built and simulated in the same MATLAB/Simulink environment. The study successfully decreased the chattering effect caused by the switching gain owing to the high activity of the control input.

26 August 2024 in FUOYE Journal of Engineering and Technology
Verified
Journal Article
Open access
PDF file
OTOmokhafe Tola
Omokhafe Tola
ETEli Taidi
Eli Taidi
BABabatunde Adegboye
Babatunde Adegboye
EYENESI ASIZEHI YAHAYA
ENESI ASIZEHI YAHAYA
OIOvis Irefu
Ovis Irefu
The sustainability of any nation's development depends on an adequate and consistent supply of energy. However, using and converting primary energy leads in energy waste, which raises the cost of energy. The study focused on energy audit and power quality issues at Sunti Golden Sugar Company (SGSC) since it has been observed that, on average, 45.12kWh of energy is needed to crush one ton of sugarcane, compared to the suggested standard of 35kWh. During the plant tour, sources of energy waste were noted, including the use of underloaded motors. In addition, the issues with harmonics in the power system brought on by the significant number of non-linear loads frequently result in motor overheating. This leads to motor burnout, as well as false tripping of protective relays, which results in an unnecessary downtime. Similarly, certain standard motors that were underloaded were found using the Motor Master software, and proper replacement with premium energy-efficient motors was recommended. As a result of replacing ordinary motors with energy-efficient motors, that is, replacing under-load motors with properly sized motors, payback period ranging from 1.17 to 5.85 years, the energy savings of 71,605kWh/year and cost savings of €3,938.00 per year which is equivalent to ₦3,256,579.05 was achieved. Shunt Hybrid Power Filters (SHPF) are designed and simulated in order to reduce current harmonics using MATLAB/Simulink software. As a result, the Total Harmonics Distortion (THD)% for Current Source Inverter (CSI) is reduced for the source current from 20.41% to 7.33% and the load current from 24.31% to 7.44%, respectively. While in the case of Voltage Source Inverter (VSI), the THD% is reduced from 17.99% to 6.67% for supply current and 20.20% to 9.62% for load current, respectively.