Redox stabilities of the hydrogen electrode with in situ exsolved Fe–Ni nanoparticles from Sr2Fe1.4Ni0.1Mo0.5O6−δ (SFMNi) perovskite are studied by analyzing the evolution of the phase composition and morphology during the redox cycles. It is found that certain amount of the exsolved nanoparticles have been oxidized to the transition metal oxide (Ni,Fe)O instead of reincorporating into the parent perovskite lattice upon re-oxidizing at 800 °C in air. However, the (Ni,Fe)O secondary phases show no adverse effect on the subsequent reduction treatment. The redox reversibility mechanism is explained by the regular-solution model. The electrodes are almost fully recovered in the reducing atmosphere, and the symmetrical cells measured under 9.7% H2–3% H2O–87.3% N2 conditions show a stable specific area polarization resistance of around 1.93 Ω cm2 at 800 °C during 13 redox cycles. Single cells using the Ni–Fe nanoparticles structured electrode exhibit a stable electrode polarization resistance of about 0.598 Ω cm2 at 800 °C under open circuit voltage conditions and a steady electrolysis current density of about −653 mA cm−2 at 1.5 V during the steam electrolysis process over 5 redox cycles. These results indicate that the SFMNi material is a very promising electrode candidate for steam electrolysis application with robust redox reversibility.
Metallic nanoparticles structured perovskite oxides prepared by the in situ exsolution method are widely utilized as alternative anodes for solid oxide fuel cells. In this work, SrxFe1.3Ni0.2Mo0.5O6−δ (SFNMx, x = 1.90, 1.95, 2.00, and 2.05) materials are prepared to construct Ni–Fe alloy nanoparticles structured SFNMx anodes. It is found that the microstructure as well as electrochemical activity of SFNMx anodes can be successfully manipulated by altering A-site Sr non-stoichiometry. Moreover, the electrochemical performance of the symmetrical cells with SFNMx electrodes demonstrates that A-site Sr deficiency can effectively accelerate the exsolution of Ni–Fe alloy nanoparticles from the parent oxides, reasonably providing more active sites for the hydrogen oxidation reaction and effectively lowering the electrode polarization resistance to 1.04 Ω cm2 with decreasing Sr content to 1.95, which is in good agreement with the results predicted by the regular-solution model. In addition, the distribution of relaxation times analysis results indicate that H2 adsorption/dissociation/ionization, which can be strongly accelerated by in situ exsolved Ni–Fe alloy nanoparticles, is the predominant rate-limiting step. It is concluded that A-site non-stoichiometry in perovskites can greatly facilitate the exsolution of metallic nanoparticles, and enable effectively enhanced electrochemical activity. Our findings can guide the development of nano-architectures of A1−xBO3 materials for other energy conversion and storage devices.
9 March 2019 in Physical Chemistry Chemical Physics
Diamond-like films (DLC) are an exceptional engineering material with excellent performance such as high hardness, low friction coefficient, superior wear resistance and chemical inertness. However, two major problems of high internal stress and poor thermal stability have seriously limited its industrial applications. In particular, the microstructures and properties of pure DLC films are highly sensitive to high temperature. Therefore, the purpose of this study is to investigate the effect of annealing temperature on the microstructures of the as-prepared films. Ti-doped DLC multilayer films were synthesized by closed field unbalanced magnetron sputtering. The as-deposited films were annealed in the range of 200 to 800 °C. The surface morphology, phase structure and bonding structure of the films were characterized by SEM, AFM, GIXRD and Raman spectroscopy. The resulting films remained a smooth surface after annealing and maintained the nature of amorphous carbon up to 600 °C. The formed phases of graphite carbon and TiC nanocrystallines occur above 600 °C. In addition, the D- and G-bands showed a significant blue shift and the FWHMG shows a declining trend up to 600 °C. This result revealed that the films had high graphitization temperature and good thermal stability due to the formation of TiC nanocrystallines and its novel structure design containing elemental doping, multilayer structuring and functionally graded layering.