The optical band-gap energy of a nanostructured tungsten trioxide film is determined using the photoacoustic spectroscopy method under continuous light excitation. The mechanism of the photoacoustic signal generation is discussed. The band-gap energy is also computed by other methods. The absorption coefficient as well as the band-gap energy of three different crystal structures of tungsten trioxide is calculated by a first-principles Green’s function approach using the projector augmented wave method. The theoretical study indicates that the cubic crystal structure shows good agreement with the experimental data.

The aim of this study was to investigate the diffusion dynamics of 25% hydrogen peroxide (H₂O₂) through enamel-dentin layers and to correlate it with dentin’s structural alterations. Micro-Raman Spectroscopy (MRS) and Fourier Transform Infrared Photoacoustic Spectroscopy (FTIR-PAS) were used to measure the spectra of specimens before and during the bleaching procedure. H₂O₂ was applied to the outer surface of human enamel specimens for 60 minutes. MRS measurements were performed on the inner surface of enamel or on the subsurface dentin. In addition, H₂O₂ diffusion dynamics from outer enamel to dentin, passing through the dentin-enamel junction (DEJ) was obtained with Raman transverse scans. FTIR-PAS spectra were collected on the outer dentin. MRS findings revealed that H₂O₂ (O-O stretching µ-Raman band) crossed enamel, had a more marked concentration at DEJ, and accumulated in dentin. FTIR-PAS analysis showed that H₂O₂ modified dentin’s organic compounds, observed by the decrease in amides I, II, and III absorption band intensities. In conclusion, H₂O₂ penetration was demonstrated to be not merely a physical passage through enamel interprismatic spaces into the dentinal tubules. H₂O₂ diffusion dynamics presented a concentration gradient determined by the chemical affinity of the H₂O₂ with each specific dental tissue.

Onychomycosis is a chronic fungal infection of nails, commonly caused by dermatophyte fungi, primarily species of Trichophyton. Because of the limited drug arsenal available to treat general fungal infections and the frequent failure of onychomycosis treatment, the search for new therapeutic sources is essential, and topical treatment with natural products for onychomycosis has been encouraged. Propolis, an adhesive resinous compound produced by honeybees (Apis mellifera), has shown multiple biological properties including significant antifungal and anti-biofilm activities in vitro. In spite of promising in vitro results, in vivo results have not been reported so far. This study assessed an ethanol propolis extract (PE) as a topical therapeutic option for onychomycosis, including its characterization in vitro and its applicability as a treatment for onychomycosis (from bench to clinic). The in vitro evaluation included analysis of the cytotoxicity and the antifungal activity against the planktonic cells and biofilm formed by Trichophyton spp. We also evaluated the capacity of PE to penetrate human nails. Patients with onychomycosis received topical PE treatments, with a 6-month follow-up period. The results of the in vitro assays showed that PE was non-toxic to the cell lines tested, and efficient against both the planktonic cells and the biofilm formed by Trichophyton spp. The results also showed that PE is able to penetrate the human nail. The results for PE applied topically to treat onychomycosis were promising, with complete mycological and clinical cure of onychomycosis in 56.25% of the patients. PE is an inexpensive commercially available option, easy to obtain and monitor. Our results indicated that PE is a promising natural compound for onychomycosis treatment, due to its ability to penetrate the nail without cytotoxicity, and its good antifungal performance against species such as Trichophyton spp. that are resistant to conventional antifungals, both in vitro and in patients.

A general and complete theoretical model of the time-resolved thermal mirror method for the measurement of thermo-optical-mechanical properties of solid materials is developed. The laser-induced temperature profile in a sample and its thermoelastic surface displacement are derived. The center intensity of a probe beam at the detector plane is calculated using the Fresnel diffraction theory. Additionally, simplified models for high and low optical absorption samples are presented, and the suitability of the simplified models is also analyzed. The influence of experimental parameters on the sensitivity of the thermal mirror method is discussed for the optimization of the experimental apparatus. The presented model and the experimental technique can be used to quantitatively determine the physical properties of transparent and opaque solids.