We report the development of novel modes of operation for electrochemical disinfection of E. coli in human urine simulant with an aim to minimize the energy required for disinfection. The system employs boron-doped diamond electrodes and will be part of an energy neutral, water and additive free outdoor toilet being developed for use in developing countries. Disinfection had been previously demonstrated with voltage being continuously applied to the electrode until disinfection was achieved. In the present study, a new pulsed mode of operation is investigated. This includes a continuous on mode, where oxidants are generated until disinfection is achieved, a single cycle mode, where oxidants are generated for a fixed time and the water is circulated so allow already generated oxidants to disinfect, and a pulsed mode with different duty cycles, which is like the single cycle mode but with multiple cycles. Disinfection was achieved with pulsed mode operation with a 68% energy reduction compared to the continuous on mode. Energy saving was most likely achieved by lengthening the contact time of the disinfectant with the bacteria and increased generation of non-chlorine disinfecting oxidants.
25 April 2018 in Journal of the Electrochemical Society
Integration of an organic photovoltaic (PV) with carbon-based supercapacitors (SCs) into a system for solar energy harvesting and storage is interesting for off-grid applications such as mobile electronics and sensor systems. Presented here is a conversion and control circuit (CC) on a flexible polyimide substrate in an integrated flexible energy harvesting and storage device compatible with roll-to-roll manufacturing (R2R). The CC is capable of PV max power-point tracking, DC-DC voltage boost of the PV output across a bank of four SCs, and charge balancing across the bank of SCs. This system is compared to a conventional direct connection between the PV and the SCs. More energy can be harvested from the PV and stored in the SC bank when using the CC to drive the PV at peak power, boost the output voltage, and balance it across serial connection of SCs. Finally, the CC, PV, and SCs are mounted to a 3D printed substrate and circuit which is used to power a wearable sensor. Due to these benefits and ability to be integrated with R2R, the presented CC provides a practical means of improving wearable solar energy harvesting and storage systems.
Electrochemical disinfection (ECD) has become an important blackwater disinfection technology. ECD is a promising solution for the 2 billion people without access to conventional sanitation practices and in areas deficient in basic utilities (e.g., sewers, electricity, waste treatment). Here, we report on the disinfection of blackwater using potential cycling compared to potentiostatic treatment methods in chloride-containing and chloride-free solutions of blackwater (i.e., untreated wastewater containing feces, urine, and flushwater from a toilet). Potentiodynamic treatment is demonstrated to improve disinfection energy efficiency of blackwater by 24% and 124% compared to static oxidation and reduction methods, respectively. The result is shown to be caused by electrochemical advanced oxidation processes (EAOP) and regeneration of sp2-surface-bonded carbon functional groups that serve the dual purpose of catalysts and adsorption sites of oxidant intermediates. Following 24 h electrolysis in blackwater, electrode fouling is shown to be minimized by the potential cycling method when compared to equivalent potentiostatic methods. The potential cycling current density is 40% higher than both the static oxidative and reductive methods. This work enhances the understanding of oxygen reduction catalysts using functionalized carbon materials and electrochemical disinfection anodes, both of which have the potential to bring a cost-effective, energy efficient, and practical solution to the problem of disinfecting blackwater.
In this work, resonant infrared matrix-assisted pulsed laser evaporation (RIR-MAPLE), a novel deposition technique, was used to produce a transparent composite electrode of polyflourene (PFO) and two-dimensional (2D) Ti3C2Tx nanosheets, which are part of the broader MXene family of transition metal carbides and nitrides. This deposition technique offers a facile way to vary film composition in polymer/polymer and polymer/nanoparticle films. Through this method, composite PFO and MXene films were studied across six different compositions, enabling the identification of a film composition that exhibited excellent charge storage (above 10 mF/cm2) and transparency (over 75% transmittance) when used as a supercapacitor electrode material. Thus, RIR-MAPLE shows promise as a controllable and facile deposition technique for organic/inorganic composite films for use in transparent supercapacitors, as well as in other energy storage applications.