This research investigates the flexural performance of slabs reinforced with high-strength steel-strand mesh (HSSM) and engineered cementitious composites (ECCs). By employing finite element analysis (FEA) and theoretical modeling, this study aims to deepen the understanding of how these materials behave under bending stresses. A finite element model was developed to simulate the nonlinear behavior of ECCs during bending, considering critical elements such as tensile and compressive damage, as well as bond–slip interactions between the steel strands and the ECCs. Furthermore, a theoretical model was created to predict the load-bearing capacity of HSSM-reinforced ECC slabs, incorporating variables like reinforcement ratios, slab dimensions, and material characteristics. The findings reveal that increasing the reinforcement ratio substantially enhances both flexural stiffness and load-bearing capacity while reducing deflection. Comparisons between the FEA results, the theoretical forecasts, and the experimental observations show close alignment, validating the proposed models. This work provides important insights for optimizing the design of HSSM-reinforced ECC slabs, highlighting their potential improvements in structural systems that demand high flexural performance.
To investigate the mechanical properties of high-strength stainless steel wire mesh (HSSSWM) in Engineering Cementitious Composites (ECCs) and determine a reasonable lap length, a total of 39 specimens in 13 sets were designed and fabricated by considering the diameter of the steel strand, spacing of the transverse steel strand, and lap length. The lap-spliced performance of the specimens was tested through a pull-out test. The results revealed two failure modes in the lap connection of steel wire mesh in ECCs: pull-out failure and rupture failure. The spacing of the transverse steel strand had little effect on the ultimate pull-out force, but it restricted the slip of the longitudinal steel strand. A positive correlation was found between the spacing of the transverse steel strand and the slip amount of the longitudinal steel strand. With an increase in lap length, the slip amount and ‘lap stiffness’ to peak load increased, while the ultimate bond strength decreased. Based on the experimental analysis, a calculation formula for lap strength considering the correction coefficient β was established.
In order to investigate the interfacial bonding properties of high-strength steel stainless wire mesh-reinforced ECC (HSSWM-ECC) and concrete, a finite element model was established for two types of interfaces based on experimental research. The results show that the failure modes observed in the 21 groups of simulations can be classified into three categories: debonding failure, ECC extrusion failure and concrete splitting failure. The failure mode was mainly affected by the type of interface. The effective anchorage length is inversely proportional to the strength of the concrete and proportional to the stiffness and thickness of the HSSWM-ECC. The capacity of the roughening interface is positively correlated with the concrete strength and bonding length, but negatively correlated with the interfacial width ratio. Increasing both the number and width of grooves within the effective range enhances the interfacial capacity, whereas higher concrete strengths tend to reduce it. Based on the above results, calculation models for the effective anchorage length and bearing capacity were established separately for the two types of interfaces. The theoretical model for the interfacial bonding property between HSSWM-ECC and concrete has been refined. These advancements establish a theoretical groundwork for the design of concrete structures strengthened with HSSWM-ECC.
Pre-existing damage in reinforced concrete (RC) beam–column joints may induce strain incompatibility between the original member and subsequently applied strengthening layers, limiting the applicability of conventional flexural-capacity models. This study experimentally and analytically investigates pre-damaged RC beam–column joints strengthened with high-strength steel strand wire mesh-reinforced engineered cementitious composite (HSSWM–ECC). Eight specimens were tested to evaluate the effects of pre-damage level, steel strand spacing, and axial compression ratio on beam-end flexural behavior. HSSWM–ECC effectively suppressed crack localization and concrete spalling, and all strengthened specimens ultimately exhibited beam-end flexural failure while the columns and joint cores remained largely intact. Compared with the unstrengthened specimen, the peak load increased by 39.24–63.88%. Reducing the strand spacing from 70 to 30 mm increased the peak load by 8.86%, whereas the higher pre-damage level caused an 11.28% reduction relative to the undamaged strengthened specimen. Within the investigated axial compression ratio range of 0.2–0.4, the difference in peak load remained below 3.64%, whereas increasing axial compression was associated with more pronounced post-peak strength degradation. Based on sectional force equilibrium and the plane-section assumption, an analytical model was developed by incorporating damage-induced strain lag and the contribution of the wrap-around side strengthening layers. The predicted capacities of the seven strengthened specimens agreed well with the experimental results, with deviations within 7%. The proposed model provides a rational approach for evaluating the beam-end flexural capacity of pre-damaged RC beam–column joints strengthened with HSSWM–ECC within the investigated parameter range and flexure-dominated failure mode.