Steinberg’s theory, which is based on the fatigue failure theory, has been widely used for predicting the structural safety of solder joints in aerospace electronic units under vibration during launches. However, theoretical limitations are encountered when evaluating the structural safety of highly integrated electronic packages mounted on printed circuit boards (PCBs) under various boundary conditions. Therefore, in our previous study, a PCB-strain-based methodology was proposed to overcome the technical limitations of the conventional Steinberg theory, and its effectiveness was validated by conducting fatigue life tests on various types of specimens, such as the ball grid array, column grid array, and quad flat package. In this study, the aim was to increase its completeness and reliability by targeting small outline packages (SOPs) that have not yet been considered. The finite element (FE) model of the SOP was proposed to guarantee the reliable prediction of the structural safety of the solder joints used in the PCB-strain-based methodology. The proposed modeling technique contributes to enable the rapid construction of an FE model for the electronic unit because it was greatly simplified into a zero-dimensional lumped mass and rigid link element to simulate the package mass and solder joint, respectively. The effectiveness of the methodology was validated by performing fatigue life tests on PCB specimens under various boundary conditions. Those experimental and analytical results indicated that the proposed methodology was much more effective in predicting the structural safety of a solder joint for various cases of tested specimens compared with the Steinberg’s theory. The simplified FE model of SOP with the rigid link element connected to six points on the package mounting area of the PCB was effective for estimating margin of safety of solder joint. The results of this study would contribute to increase the availability of the proposed methodology for rapid mechanical design of electronic units in aerospace industries.
A novel passive vibration-damping device is proposed and investigated for a large deployable solar array. One strategy for achieving high damping in a solar panel is using a yoke structure comprising a hyperelastic shape memory alloy and multiple viscous adhesive layers of acrylic tape. The effectiveness of the proposed system in achieving a high damping performance was demonstrated by conducting free vibration and low-level sine sweep tests using a solar array, and a 0.75-m-long flexible dummy structure was simulated. We also investigated the dependence of the damping performance of the proposed structure on the number of viscous lamina layers. Finally, the damping characteristics of the proposed system were assessed under predictable on-orbit temperature conditions.
In the space environment, the elastic vibrations of satellite solar panels are caused by various factors that disturb satellite missions. Therefore, we propose a multi-layered high-damping yoke structure based on a passive control method. To optimize the proposed yoke structure, we performed a free vibration test on various multi-layered blade specimens and designed a yoke structure with the maximum damping performance based on the test results. This high-damping yoke structure was mounted on a dummy solar panel with flexible mode (0.79 Hz) and basic characteristic tests were performed to validate the effectiveness of the solar panel vibration suppression. The test results demonstrated that the proposed multi-layered high-damping yoke is effective in suppressing the vibrations of the first and second modes. In addition, a thermal vacuum test was performed to investigate the delamination between multi-layered structures, and the test results proved the applicability of the proposed yoke structure in an actual space environment.
The Oh-Park methodology was proposed to overcome the limitations of Steinberg’s theory for evaluating the structural safety of space-borne electronics and has been experimentally verified at the printed circuit board (PCB) specimen level for various types of electronic packages, such as ball grid arrays (BGAs), column grid arrays (CGAs), and small-outline packages (SOPs). However, it is necessary to validate the design methodology because the PCB mounted on the housing is affected by the elastic mode of the mechanical housing. In addition, although the validity of the existing theory based on critical strain has been verified for horizontally mounted structures, there are cases where PCBs are mounted vertically. Therefore, it is essential to consider the dynamic influence of the boundary conditions of mounted electronics. In this study, electronics specimens with corresponding boundary conditions were fabricated, and a fatigue-life test was performed. In addition, a structural analysis using Steinberg’s theory and the Oh-Park methodology was performed, and the results were compared with those of the fatigue-life test. The results showed that the analysis using the Oh-Park methodology accurately represented the test results, and the validity of the Oh-Park methodology for vertical electronics was verified experimentally.
A critical-strain-based methodology was proposed to overcome the theoretical limitations of Steinberg’s method, and its effectiveness was experimentally verified through fatigue tests of ball grid arrays, column grid arrays, and lead-type specimens on printed circuit boards (PCBs) with various boundary conditions. These verifications were performed only on PCB units with a single electronic package mounted. However, in actual industrial fields, electronics with various types of electronic packages mounted comprehensively are mainly applied to electronics combined in a mechanical housing structure. Therefore, the verification of the corresponding methodology for the above actual conditions is essential. This study aimed to validate the theoretical feasibility of the design technique under the condition that the elastic mode vibration of a mechanical housing structure acts complexly on PCBs. The proposed methodology was validated analytically and experimentally through a vibration test on a comprehensive PCB specimen with various types of electronic packages mounted on electronic mechanical housing structures.