We focus on optimization of dynamic spectrally-spatially flexible optical networks (SS-FONs), in which distance-adaptive, spectral super-channel (SCh) transmission is realized over weakly-coupled multi-core fibers (MCFs). In such networks, the inter-core crosstalk (XT) effect in MCFs impairs the quality of transmission (QoT) of optical signals, which has a negative impact on overall network performance. In this context, a key issue is selection of a modulation format (MF) for a particular lightpath, since each MF offers a different tradeoff between spectral efficiency (number of occupied frequency slices) and transmission reach, and both these elements are in a close relation with the experienced XT. In fact, it is difficult to quantify the impact of the MFs used in a given network on the deterioration in QoT due to the XT effect and on overall network performance, as the levels of XT experienced by particular lightpaths depend directly on ongoing transmissions in neighbor MCF cores, and those (i.e., established lightpaths) are subject to stochastic changes in dynamic SS-FONs. Therefore, in this work, we propose an approach that selects a MF for a lightpath based only on the transmission distance, i.e., length of the applied routing path. In particular, for each considered MF, we define a Modulation format Distance Limit (MDL) parameter that is used to select the MF for a lightpath by a simple comparison of the considered routing path length against the MDL parameter. To facilitate the very complex process of determining the best values of the MDL parameter, we propose a machine learning (ML) approach, namely, supervised learning regression method, with the overall goal to optimize network performance in terms of bandwidth blocking probability (BBP). Extensive simulation experiments performed in different network scenarios show that the proposed method ML allows to achieve performance gains when compared to various reference approaches, including a more computationally expensive method that is based on dynamic (flexible) selection of MFs.
This work concentrates on the problem of optimizing the cost of a passive wavelength division multiplexing (WDM) optical network used as a transport network for carrying the xHaul packet traffic between a set of remote radio sites and a central hub in a 5G radio access network (RAN). In this scope, we investigate the flexible use of optical add-drop multiplexers (OADMs) for the aggregation of traffic from a number of remote sites, where the type/capacity of optical devices—OADMs and optical multiplexers (MUXs)—is selected in accordance with the traffic demand. The approach is referred to as Flex-O. To this end, we formulate the xHaul network planning problem consisting in the joint provisioning of transmission paths (TPs) between the remote sites and the hub with optimized selection and placement of OADMs on the paths and proper selection of MUXs at the ends of the TPs. The problem formulation takes into accounts the optical power budget that limits the maximum transmission distance in a function of the amount and type of optical devices installed on the TPs. The network planning problem is modeled and solved as a mixed-integer linear programming (MILP) optimization problem. Several network scenarios are analyzed to evaluate the cost savings from the flexible (optimized) use of OADMs. The scenarios differ in terms of the availability of OADMs and the capacity of the WDM devices applied on the TPs. The numerical experiments performed in three mesh networks of different size show that the cost savings of up to between 35 and 45% can be achieved if the selection of OADMs is optimized comparing to the networks in which either single-type OADMs are used or the OADMs are not applied.
We focus on the optical signal-to-noise ratio (OSNR)-aware optical path (lightpath) planning problem in spectrally and spatially flexible optical networks (SS-FONs) connected using weakly coupled multi-core fibers (MCFs) in which distance-adaptive and super-channel transmission is realized using multiple modulation formats. In the SS-FON considered, the quality of transmission (QoT) of optical signals is degraded due to the inter-core crosstalk (XT) effect occurring in MCFs. To account for the XT impairment when planning lightpath connections, we make use of a reliable QoT model based on the OSNR estimation, in which the XT impairment is integrated with other physical-layer impairments. To model the lightpath planning optimization problem, we develop a novel mixed-integer programming (MIP) formulation that incorporates the OSNR model. In addition, we propose an efficient heuristic method that is capable of solving larger instances of the optimization problem considered. The results of numerical experiments indicate the low scalability of the MIP method due to the presence of XT and high effectiveness of the heuristic method. The analysis of three different network topologies and two types of MCFs shows a high impact of XT on network performance and limited performance gains from the presence of the central core in a 7-core MCF.
We present a theoretical and experimental investigation of unrepeatered transmission over standard single-mode fiber (SMF-28) using several schemes of distributed Raman amplification, including first, second, and dual order. In order to further extend the transmission distance, we utilize advanced bidirectional higher-order ultra-long Raman fiber laser-based amplification, where we use fiber Bragg gratings (FBGs) to reflect Stokes-shifted light from the secondary pumps. Our work demonstrates the possibility of transmission up to 240-km span length with a total span loss of 52.7 dB. Here, we use a 28-Gbaud signal using a 64-quadrature amplitude modulation (QAM) modulation format. Our results highlight the contribution of nonlinear compensation using digital back propagation in a digital signal processor (DSP) code at the receiver.
One of the main challenges in dense 5G radio access networks (RANs) is provisioning of low-cost connectivity between a large number of antennas, located at remote sites, and a central site (hub) in which baseband processing functions are performed. Packet-switched Ethernet and wavelength division multiplexing (WDM) are two principal transport network technologies enabling the reduction of the demand for direct optical fiber connections between the antennas and the hub. Whereas Ethernet allows for statistical multiplexing of multiple xHaul (fronthaul/midhaul/backhaul) flows and their aggregation in a high-capacity transmission link, WDM makes it possible to establish a number of such links (using different wavelengths) in a single optical fiber. Additional savings in the amount of fibers required can be achieved by means of optical add-drop multiplexers (OADMs) that allow for obtaining access to unused wavelengths by intermediate remote nodes, whenever the capacity on the WDM system is not fully utilized by the end remote node. In this work, we focus on the problem of planning optimal fiber connections, including the placement of OADMs for a set of wavelength demands at remote sites, with the aim of minimizing the amount of fibers used in a packet-optical xHaul access network carrying 5G traffic. We consider a passive WDM system in which the maximum transmission distance, estimated using an optical power-budget model, depends on the number of OADMs that are present on the transmission path. To formulate and solve the optimization problem, we make use of integer linear programming (ILP). We apply the ILP model in network analysis. In particular, by means of numerical experiments performed for two different network topologies, we study the impact of traffic load (in terms of the number of requested wavelengths) and optical multiplexer loss on the number of transmission paths that have to be established in the network. Obtained results show that the savings in fiber connections of up to can be achieved in a packet-optical xHaul network if OADMs are used when compared to the scenario without OADMs.
30 September 2021 in Journal of Telecommunications and Information Technology
Fire-resistant fiber optic cables used in safety and monitoring systems playing an essential role in fire fighting and building evacuation procedures are required to temporarily maintain optical continuity when exposed to fire. However, the use of fused silica fiber at temperatures between 800◦C and 1000◦C is associated with two highly undesirable phenomena. Thermal radiation (incandescence) of optical fibers, with its intensity and spectral distribution being proportional to additional attenuation observed in the fiber’s hydroxyl absorption bands (“water peaks”) is one of them. The other consists in penetration of thermal radiation from the surroundings into the fiber, due to defects in glass, causing light scattering and resulting in fiber brittleness. Thermal radiation is a source of interference in fiber attenuation measurements performed during fire tests and affects normal operation of fiber optic data links in the event of a fire. In this article, results of laboratory tests performed on a telecom single mode and multimode fibers subjected to temperatures of up to 1000◦C are presented.