One useful technique for increasing the efficiency of organic dye-sensitized solar cells (DSSCs) is to extend the π-conjugated bridges between the donor (D) and the acceptor (A) units. The present study used the DFT and TD–DFT techniques to investigate the effect of lengthening the polyene bridge between the donor N, N-dimethyl-anilino and the acceptor dicyanovinyl. The results of the calculated key properties were not all in line with expectations. Planar structure was associated with increasing the π-conjugation linker, implying efficient electron transfer from the donor to the acceptor. A smaller energy gap, greater oscillator strength values, and red-shifted electronic absorption were also observed when the number of polyene units was increased. However, some results indicated that the potential of the stated dyes to operate as effective dye-sensitized solar cells is limited when the polyene bridge is extended. Increasing the polyene units causes the HOMO level to rise until it exceeds the redox potential of the electrolyte, which delays regeneration and impedes the electron transport cycle from being completed. As the number of conjugated units increases, the terminal lobes of HOMO and LUMO continue to shrink, which affects the ease of intramolecular charge transfer within the dyes. Smaller polyene chain lengths yielded the most favorable results when evaluating the efficiency of electron injection and regeneration. This means that the charge transfer mechanism between the conduction band of the semiconductor and the electrolyte is not improved by extending the polyene bridge. The open circuit voltage (V_OC) was reduced from 1.23 to 0.70 V. Similarly, the excited-state duration (τ) decreased from 1.71 to 1.23 ns as the number of polyene units increased from n = 1 to n = 10. These findings are incompatible with the power conversion efficiency requirements of DSSCs. Therefore, the elongation of the polyene bridge in such D-π-A configurations rules out its application in solar cell devices.

A major challenge in improving the overall efficiency of dye-sensitized solar cells is improving the optoelectronic properties of small molecule acceptors. This work primarily investigated the effects of conjugation in nitriles incorporated as acceptor moieties into a newly designed series of D-A-A dyes. Density functional theory was employed to specifically study how single–double and single–triple conjugation in nitriles alters the optical and electronic properties of these dyes. The Cy-4c dye with a highly conjugated nitrile unit attained the smallest band gap (1.80 eV), even smaller than that of the strong cyanacrylic anchor group (2.07 eV). The dyes lacking conjugation in nitrile groups did not contribute to the LUMO, while LUMOs extended from donors to conjugated nitrile components, facilitating intramolecular charge transfer and causing a strong bind to the film surface. Density of state analysis revealed a considerable impact of conjugated nitrile on the electronic properties of dyes through an effective contribution in the LUMO, exceeding the role of the well-known strong 2,1,3-benzothiadiazole acceptor unit. The excited state properties and the absorption spectra were investigated using time-dependent density functional theory (TD-DFT). Conjugation in the nitrile unit caused the absorption band to broaden, strengthen, and shift toward the near-infrared region. The proposed dyes also showed optimum photovoltaic properties; all dyes possess high light-harvesting efficiency ($LHE$) values, specifically 96% for the dyes Cy-3b and Cy-4c, which had the most conjugated nitrile moieties. The dyes with higher degrees of conjugation had longer excitation lifetime values, which promote charge transfer by causing steady charge recombination at the interface. These findings may provide new insights into the structure of conjugated nitriles and their function as acceptor moieties in DSSCS, which may lead to the development of extremely effective photosensitizers for solar cells.

This work investigated the substitution of the aldehyde with a pyran functional group in D-π-aldehyde dye to improve cell performance. This strategy was suggested by recent work that synthesized D-π-aldehyde dye, which achieved a maximum absorption wavelength that was only slightly off the threshold for an ideal sensitizer. Therefore, DFT and TD-DFT were used to investigate the effect of different pyran substituents to replace the aldehyde group. The pyran groups reduced the dye energy gap better than other known anchoring groups. The proposed dyes showed facile intermolecular charge transfer through the localization of HOMO and LUMO orbitals on the donor and acceptor parts, which promoted orbital overlap with the TiO₂ surface. The studied dyes have HOMO and LOMO energy levels that could regenerate electrons from redox potential electrodes and inject electrons into the TiO₂ conduction band. The lone pairs of oxygen atoms in pyran components act as nucleophile centers, facilitating adsorption on the TiO₂ surface through their electrophile atoms. Pyrans increased the efficacy of dye sensitizers by extending their absorbance range and causing the maximum peak to redshift deeper into the visible region. The effects of the pyran groups on photovoltaic properties such as light harvesting efficiency (LHE), free energy change of electron injection, and dye regeneration were investigated and discussed. The adsorption behaviors of the proposed dyes on the TiO₂ (1 1 0) surface were investigated by means of Monte Carlo simulations. The calculated adsorption energies indicates that pyran fragments, compared to the aldehyde in the main dye, had a greater ability to induce the adsorption onto the TiO₂ substrate.