Lead halide perovskite solar cells (PSCs) have been rapidly developed in the past decade. Owing to its excellent power conversion efficiency with robust and low-cost fabrication, perovskite quickly becomes one of the most promising candidates for the next-generation photovoltaic technology. With the development of PSCs, the interface engineering has witnessed its increasingly critical role in maximizing the device performance as well as the long-term stability, because the interfaces in PSCs are closely correlated with the defect management, carrier dynamics and surface passivation. This review focuses on interfacial modification between the perovskite active layer and the charge transport layer, as well as the recent advances on high-efficiency and stable PSCs driven by interface engineering strategies. The contributing roles of interface engineering in terms of defect passivation, inhibiting ion migration, optimization of energy band alignment and morphological control are discussed. Finally, based on the latest progress and advances, strategies and opportunities for the future research on interface engineering for PSCs are proposed to promote the development of perovskite photovoltaic technology.
The development of high‐performance dopant‐free silicon solar cells is severely bottlenecked by opaque electron selective contact. In this paper, high transmittance (80.5% on glass) and low work function (2.92 eV) lithium fluoride (LiFx)/MgFxOy electron contact stack by tailoring the composition of MgFxOy hybrid film is reported. This hybrid structure exhibits a high conductivity (2978.4 S cm−1) and a low contact resistivity (2.0 mΩ cm2). The element profile of LiFx/MgFxOy contact is measured and the reaction kinetics is analyzed. As a proof‐of‐concept, this electron selective contact is applied for dopant‐free silicon solar cells. An impressive efficiency of 21.3% is achieved on dopant‐free monofacial solar cell with molybdenum oxide (MoOx)/zinc‐doped indium oxide (IZO) hole contact. An efficiency bifaciality of 71% is obtained for dopant‐free bifacial solar cell with full‐area LiFx/MgFxOy/ITO (tin‐doped indium oxide) transparent electron contact. It is the highest efficiency bifaciality so far for dopant‐free bifacial solar cells to the best knowledge. Both cell configurations with LiFx/MgFxOy contacts show excellent environment stability. The cell efficiency maintains more than 95% of its initial value after keeping in air for 1500 h. This work provides a new idea to achieve transparent electron contact, showing a great potential for high‐efficiency and low‐cost optoelectronic devices.
19 June 2020 in Journal of Materials Science: Materials in Electronics
The aging-induced performance enhancement of the perovskite solar cells (PSCs) has been considered to be associated with the oxidation progress of the hole-transporting layer. Whereas the influence of the structural evolution of the passivation layer is underestimated. In this work, a spontaneous relaxation of two-dimensional (2D) passivation layer with increased n-value structure is observed, which can be accelerated under ambient atmosphere. It is demonstrated that device with relaxed 2D passivation layer exhibits reduced non-radiative recombination and optimized charge transfer property, contributing substantially to the aging-induced performance enhancement in 2D-3D heterostructured PSCs. Finally, a high fill factor of 84.15% of the devices is obtained with the relaxed 2D passivation layer, suggesting the spontaneous relaxation of 2D passivation layer is playing a key role in achieving high quality optoelectronic devices.
1 December 2021 in Journal of Alloys and Compounds
In recent years, perovskite solar cells have achieved high efficiency in small areas, but the industrialization of perovskite solar cells is still hampered by the efficiency loss of cells during area scaling. Series modules are currently the most widely used and effective modular process for perovskite solar cells, a process that requires the patterning of the layer stack in individual cells. This interconnection scheme consists of three lines, P1–P3, which are ablated using a pulsed laser beam. In this work, we developed an efficient perovskite module with a high geometric fill factor (GFF) based on a two-step spin-coating method by optimizing the laser ablation step. We constructed the entire device structure by means of a picosecond green pulsed laser, meanwhile, the dead area is greatly reduced by optimizing the parameters and process, and finally achieving an ultra-high GFF of over 99%. In addition, we investigated the effect of poor P2 and P3 ablation on the perovskite solar modules and compared the performance of the module before and after ablation optimization. We finally obtained a maximum photoelectric conversion efficiency of 22.79% with an aperture area of 12.6 cm2. Concurrently, we conducted electrocatalytic hydrogen production experiments on the prepared perovskite solar modules, and the experimental results have also shown excellent performance and good prospects.