To meet rising global demands for energy, the oil and gas industry continuously strives to develop innovative oilfield technologies. With the development of new enhanced oil recovery techniques, sandstone acidizing has been significantly developed to contribute to the petroleum industry. Different acid combinations have been applied to the formation, which result in minimizing the near wellbore damage and improving the well productivity. A combination of hydrofluoric acid and hydrochloric acid (HF:HCl) known as mud acid has gained attractiveness in improving the porosity and permeability of the reservoir formation. However, high-temperature matrix acidizing is now growing since most of the wells nowadays become deeper and hotter temperature reservoirs, with a temperature higher than 200 °F. As a result, mud acid becomes corrosive, forms precipitates and reacts rapidly, which causes early consumption of acid, hence becoming less efficient due to high pH value. However, different acids have been developed to combat these problems where studies on retarded mud acids, organic-HF acids, emulsified acids, chelating agents have shown their effectiveness at different conditions. These acids proved to be alternative to mud acid in sandstone acidizing, but the reaction mechanism and experimental analysis have not yet been investigated. The paper critically reviews the sandstone acidizing mechanism with different acids, problems occurred during the application of different acids and explores the reasons when matrix stimulation is successful over fracturing. This paper also explores the future developing requirement for matrix acidizing treatments and new experimental techniques that can be useful for further development, particularly in developing new acids and acidizing techniques, which would provide better results and information of topology, morphology and mineral dissolution and the challenges associated with implementing these “new” technologies.
To fulfill the demand of the world energy, more technologies to enhance the recovery of oil production are being developed. Sandstone acidizing has been introduced and it acts as one of the important means to increase oil and gas production. Sandstone acidizing operation generally uses acids, which create or enlarge the flow channels of formation around the wellbore. In sandstone matrix acidizing, acids are injected into the formation at a pressure below the formation fracturing pressure, in which the injected acids react with mineral particles that may restrict the flow of hydrocarbons. Most common combination is Hydrofluoric Acid - Hydrochloric with concentration (3% HF - 12% HCl) known as mud acid. But there are some problems associated with the use of mud acid i.e., corrosion, precipitation. In this paper several new combinations of acids were experimentally screened to identify the most effective combination. The combinations used consist of fluoboric, phosphoric, formic and hydrofluoric acids. Cores were allowed to react with these combinations and results are compared with the mud acid. The parameters, which are analyzed, are Improved Permeability Ratio, strength and mineralogy. The analysis showed that the new acid combination has the potential to be used in sandstone acidizing.
7 July 2017 in IOP Conference Series: Materials Science and Engineering
Core flooding acidizing experiments on sandstone/carbonate formation are usually performed in the laboratory to observe different physical phenomena and to design acidizing stimulation jobs for the field. During the tests, some key parameters are analyzed such as pore volume required for breakthrough as well as pressure. Hydrochloric acid (HCl) is commonly used in the carbonate matrix acidizing while Mud acid (HF: HCl) is usually applied during the sandstone acidizing to remove damage around the well bore. However, many problems are associated with the application of these acids, such as fast reaction, corrosion and incompatibility of HCl with some minerals (illite). To overcome these problems, chelating agents (HEDTA, EDTA and GLDA) were used in this research. Colton tight sandstone and Guelph Dolomite core samples were used in this study. The experiments usually are defined in terms of porosity, permeability, dissolution and pore topology. Effluent samples were analyzed to determine dissolved iron, sodium, potassium, calcium and other positive ions using Inductively Coupled Plasma (ICP). Meanwhile Nuclear Magnetic Resonance (NMR) was employed to determine porosity and pore structure of the core sample. Core flood experiments on Berea sandstone cores and dolomite samples with dimensions of 1.5 in × 3 in were conducted at a flow rate of 1 cc/min under 150oF temperature. NMR and porosity analysis concluded that applied chemicals are effective in creating fresh pore spaces. ICP analysis concluded that HEDTA showed good ability to chelate calcium, sodium, magnesium, potassium and iron. It can be established from the analysis that HEDTA can increase more amount of permeability as compared to other chelates.