In recent years, remarkable progresses have been made in the R&D efforts for high temperature superconducting (HTS) high-field magnets. The screening-current-induced magnetic field and mechanical stress/strain in rare-earth barium-copper-oxide (REBCO) coils are raising growing concerns. This paper presents experimental and theoretical analyses on the effects of screening-current-induced mechanical strains in a REBCO insert setup without transport currents. Strain measurements on two REBCO coils, with and without over-banding structures, were carried out in an low temperature superconducting (LTS) background field magnet. Electromagnetic-mechanical models were developed, coupling the tilting angles of the superconducting tapes and the strain dependency of the critical current. The discrete-coupled model with turn-to-turn contacts, the discrete-sequential model and the block model were implemented and compared against the measured hoop strains. Combining experimental data with simulation models, it is shown that moderate over-banding structures are effective in providing reinforcements for the superconductors. A new method of edge-bonding was proposed and tested, which could reduce hoop strains in low applied fields but failed in higher fields. This work could be useful for the design and analysis of future high-field REBCO magnets.

The shielding (or screening current) effect in high- T _c coated conductors has a strong influence on its stress/strain distribution in a coil winding, especially during high-field operations. To demonstrate this phenomenon, a special experimental setup was designed. With an LTS background magnet and a small HTS insert coil, we were able to carry out direct observations on the hoop strains of a 10 mm wide REBCO sample. Measured data was compared with numerical solutions obtained from models based on T – A formulation and elastic models, showing good agreement. An analytical expression was proposed to estimate the maximum radial Lorentz force considering the screening current effect. Using the developed numerical models, we further studied two methods that are utilized for reducing the screening-current-induced magnetic field, i.e. use of multi-filamentary conductors and current sweep reversal approach.

A high-resolution 1.3-GHz/54-mm low-temperature superconducting/high-temperature superconducting (HTS) nuclear magnetic resonance magnet (1.3 G) is currently being built at Francis Bitter Magnet Laboratory, Massachusetts Institute of Technology. One of its key components is an 800-MHz HTS insert (H800) comprising three nested coils. Each coil is a stack of doublepancake coils wound with 6-mm-wide 75-μm-thick REBCO tape. For this H800 generating its self-field of 18.6 T and being exposed to a total field as high as 30.5 T, overbanding each pancake coil is necessary to keep the conductor strain at <; 0.6%. Although electromagnetic and mechanical details of the H800 had been considered during its design stage, a parametric study on the overband radial build considering winding tension effect should further confirm the results of our previous analysis. Thus, in this paper, based on Maxwell's equations and the equilibrium equations for mechanical deformation, we examine stress levels that the H800 experiences as H800 undergoes winding-energizing sequences during operation at 1.3 GHz. We also discuss the effects of overband radial build and winding tension on conductor stress in each coil. Finally, based on this analysis, we may further optimize the stainless-steel overbanding and winding tension on each H800 coil.

Large Lorentz forces commonly arise from the intense field and high current in superconducting coils, which can induce maximum stress up to several hundred megapascal (MPa) in magnets. It is a big challenge in compact high-field magnets with small mechanical margin during energization. In this paper, the mechanical characteristics and strain responses of two superconducting magnets with different configurations and low-temperature superconducting (LTS) materials are investigated experimentally during their excitation process and quench events. To explore the strain behavior in the magnets, several cryogenic resistance strain gauges (CRSGs) and homemade polymer-fiber Bragg grating (FBG) sensors are used for measurements. The strain responses during excitation and quench training tests of the two LTS magnets are recorded to show that both measurement techniques have good precision and repeatability. Compared to the CRSG with complex compensation bridges, the polymer-FBG sensors exhibit more advantages like smaller size, noncircuit compensation, and insensitivity to electromagnetic interferences, and most important of all is that the polymer-FBG can be embedded in coils with good survival to measure the internal strain in the magnets. Based on FEM, we further calculated the electromagnetic field and deformation of the two magnets, and the predicted results show good agreement with the experimental data.

The rapid detection and comprehensive monitoring of quench onset and evolution in high-temperature superconducting (HTS) materials remains immensely challenging because the normal zone propagation velocity in HTS materials is two or three orders of magnitude less than that in low-temperature superconductors. In this study, we experimentally and numerically explore quench events triggered by heat spots in yttrium barium copper oxide HTS tapes to characterize the quench onset and propagation. A multiplexed fiber Bragg grating sensor with multiple gratings was used to perform highly accurate strain measurements. Conventional voltage and temperature measurements were performed synchronously on the HTS tapes. A systematic comparison of these multifield signals during quench onset and development illustrated that the evolution of thermoelastic strain and strain-rate in HTS tapes captures the quench onset and propagation. A distinct feature was exhibited during the quenching of a pre-tensioned HTS tape: the thermoelastic strain initially relaxed but subsequently increased until the strain rate exhibited a significant slope change, which corresponded to the quench onset time. The thermoelastic strain in a nearly unconstrained HTS tape gradually increased until quenching occurred. A prominent characteristic for detecting quench onset in HTS materials have been revealed based on the change in the slope of the thermoelastic strain-rate or the second derivative of the strain remaining nearly constant. For a pre-tensioned HTS tape, the minimization of the thermoelastic strain or the strain-rate becoming zero may be a predictor that preceded the quench by ∼1–2 s, which can be, to a certain extent, regarded as an early warning. Another important and novel result was the experimental demonstration of global strain responses distant from the quench location in the pre-tensioned HTS tape, while the temperature and voltage detection are commonly localized methods. The mechanism behind these thermoelastic strain characteristics was further discussed and simulated from the induced Joule heating throughout the quench event. The measurements and numerical predictions suggested a new paradigm of quench detection based on the thermoelastic strain-rate in HTS materials.

As promising magnet types, discrete-cosine-theta and canted-cosine-theta (DCT&CCT) superconducting magnets are designed for the High Energy Fragment Separator (HFRS), a fragment separator of the High Intensity Heavy Ion Accelerator Facility (HIAF). Quench protection is one of the key issues for DCT&CCT superconducting magnets due to low thermal conductivity between each turns and slow transverse quench propagation. Thermal quench-back induced by the center cooper wire as a heater automatically is a feasible quench protection option for the magnet wound with 6+1 type superconducting cables (six superconducting wires and one center cooper wire). In the present paper, an electro-thermal coupling model is developed and validated to deal with the dynamic coupling behaviors of electrical and temperature fields inside the superconducting magnets during quench protection process. The transient evolutions of current and voltage-to-ground are numerically obtained by finite element method, which shows obvious quench-back behaviors and agree well with the experimental measurements of the prototype magnet L800 in first round test. The hot-spot temperature can be reduced significantly considering quench-back effect. Furthermore, the quench protection baselines of temperature and quench integral are analyzed and predicted for L800, indicating that the magnet can be protected properly by the protection method with a quench-back at ultimate current 466A.