Thermal spray coatings are a group of coating processes that enhance the performance of parts by adding functionality to surfaces. In the past few decades, thermal spray coatings technology was used to resist wear, erosion, corrosion, cavitation, repair and dimensional restoration of parts. However, the consideration of process parameters setting develops a reliable coating having high mechanical and morphological properties for demanding coating applications. Hence the aim of this review paper is to provide an overview of distinct thermal spray coatings, historical development, hot corrosion mechanism and effect of chemical composition and alloying elements on the hot corrosion resistance of super alloys in USC power plants. Then the effects of processing conditions on the mechanical properties of distinct thermal sprayed coatings obtained at distinct process parameters are summarised. Finally, the distinct thermal post treatments such as fusing of self-flux alloys, remelting and solid heat treatments, merits, demerits and future challenges are discussed.
High-temperature corrosion of coal-fired boiler parts such as water walls and superheated tubes poses a serious threat to the efficiency of the thermal power plant. To overcome this, numbers of corrosion control techniques are commonly employed. But, a dense and defect-free coating deposited by the thermal spray technique has shown promising result to combat hot corrosion. Although open or closed porosity in distinct thermal spray coatings can originate from distinct factors such as partial or totally un-molten particles, inadequate flow or fragmentation of the molten particle at impact, non-optimal spray angle and entrapped gas. But, this can still only be prevented by coating post-treatment. Hence, in this paper, authors have reviewed the performance of distinct coatings deposited by diverse thermal spray processes. Then, the effect of distinct process parameters and heat treatments on microstructure and mechanical properties of coatings is described. Finally, the best coatings are suggested to combat maximum hot corrosion of boiler tubes.
Cold spray is an emerging surface coating technology for rapidly developing thick coating, thin films and additive manufacturing of parts at relatively low temperatures. The low cost and scalability of a cold spray method make it promising for diverse industrial applications. Presently, the cold spray coating is widely used for the production of machine parts, materials and tools that requires the desired surface properties. However, the consideration of process parameters setting develops a reliable coating having high mechanical, tribological, fatigue and morphological properties for demanding coating applications. Hence, the aim of this paper is to study the effect of processing conditions (pressure and temperature of propellant gas, powder particle morphology and post-process treatments) on the tribological and mechanical properties of cold-sprayed coatings. Further, the effect of microstructure and processing conditions on the fatigue and static characteristics of cold spray material is also discussed.
The aim of the current investigation is to evaluate the erosion-corrosion (E-C) performance of wire arc sprayed Ni-20Cr and Ni-5Al coatings on T22 and SA516 boiler steels in a real boiler environment. The microstructure, mechanical properties and high temperature E-C performance of the deposited coatings were investigated. The E-C behaviour of the test samples was determined in the superheater zone of the coal fired boiler at 750°C for fifteen cycles, where each cycle involved 100 hours of heating followed by 1hour of cooling. Thickness loss data was used to determine the E-C behaviour of the coating. XRD, SEM/EDS were used to analyse the test samples. Ni-20Cr coated SA516 steel decreased maximum E-C rates by 98.05%, while Ni-5Al coated T22 steel reduced E-C by 68.63% than the base steel. This higher E-C resistance is due to the formation of protective phases (Cr2O3, NiO and Al2O3) and better mechanical properties of the coatings.
The aim of current investigation is to access in-vitro corrosion performance of flame sprayed titania (TiO2) coated 316L stainless steel, hydroxyapatite (HAp) coated, hydroxyapatite/titania bond coated (HAp/TiO2) 316L stainless steel and plasma sprayed zirconia (ZrO2) coated 316L stainless steel. In HAp/TiO2 bond coatings, TiO2 was utilize as a bond coat between the 316L stainless steel substrate and HAp top coat. The different characterization methods such as SEM, EDS, XRD and electrochemical methods were used to analyse the electrochemical characteristics as well as microstructural morphology phases of the coatings. In addition the corrosion behavior of the coated and uncoated samples was performed in simulated body fluid. The tests were carried out for potentio-dynamic polarization and open circuit potential. The experimental results reveal that after the deposition of bond coatings (HAp, TiO2, ZrO2 and HAp/TiO2) the corrosion resistance of the steel was observed to increase.
13 December 2022 in Journal of Failure Analysis and Prevention