Samuel Bayham

Dr. Samuel Bayham

orcid

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2015 in Applied Energy
Verified
Journal Article
Closed access
LZLiang Zeng
Liang Zeng
ATAndrew Tong
Andrew Tong
MKMandar Kathe
Mandar Kathe
SBSamuel Bayham
Samuel Bayham
LFLiang-Shih Fan
Liang-Shih Fan

21 October 2023 in Energy Conversion and Management
Verified
Journal Article
Closed access
BZBiao Zhang
Biao Zhang
NHNor Farida Harun
Nor Farida Harun
NZNana Zhou
Nana Zhou
JCJose J. Colon-Rodriguez
Jose J. Colon-Rodriguez
DODanylo Oryshchyn
Danylo Oryshchyn
SBSamuel Bayham
Samuel Bayham

3 August 2017 in Industrial & Engineering Chemistry Research
Verified
Journal Article
Open access
EMEsmail R. Monazam
Esmail R. Monazam
RBRonald Breault
Ronald Breault
DFDaniel J. Fauth
Daniel J. Fauth
LSLawrence J. Shadle
Lawrence J. Shadle
SBSamuel Bayham
Samuel Bayham
Thermogravimetric analysis was employed to investigate the CO2 and H2O adsorption rates and water vapor equilibrium on anhydrous and prehydrate linear polyethylenimine (LPEI) sorbent impregnated within a commercially functional CARiACT G10 (HPV) silica support. Water vapor experiments utilizing specific humidities of 2%, 8%, and 16% in contact with an anhydrous PEI sorbent resulted in proportional quantities of water vapor uptake. Subsequently, both anhydrous and prehydrated PEI-impregnated sorbents were made available to identical humidified gaseous streams containing a CO2 concentration of 10% at 60 °C. CO2 capacity increased dramatically in the presence of different levels of humidity. Various kinetic models were systematically employed to interpret the experimental data including single- and multiple-step models. The rate data was best represented by a reaction mechanism pathway involving the interplay of CO2 with PEI-impregnated sorbents exhibiting a quick adsorption phase followed by a slow approach to equilibrium. Moreover, a phenomenological rate model was developed to describe the dynamic H2O and CO2 uptakes at specific humidity levels studied. The kinetic study showed good agreement with experimental data. Furthermore, the effects observed during the adsorption and hydration are shown to be complementary to known chemical and physical transformations within the polyethylenimine’s macromolecule.

3 May 2023 in International Journal of Hydrogen Energy
Verified
Journal Article
Closed access
JRJarrett Riley
Jarrett Riley
MBMichael Bobek
Michael Bobek
CAChris Atallah
Chris Atallah
RSRanjani Siriwardane
Ranjani Siriwardane
SBSamuel Bayham
Samuel Bayham

13 July 2021 in IEEE Transactions on Power Systems
Verified
Journal Article
Closed access
RPRupen Panday
Rupen Panday
NHNor Farida Harun
Nor Farida Harun
BZBiao Zhang
Biao Zhang
DMDaniel Maloney
Daniel Maloney
DTDavid Tucker
David Tucker
SBSamuel Bayham
Samuel Bayham
Kinetic energy available from the turbomachinery may boost short-term ramp rates during load shifting between generator and fuel cell that may be exploited to optimize the performance of turbine-fuel cell hybrid systems during load following. The paper starts with modeling a gas turbine, gearbox, and generator sitting on the rigid shafts as a two-mass model primarily for estimating the rotational inertia available from the turbogenerator. The gas turbine and its environment impose constraints of available space allowances, measurements from high-speed rotating parts, lack of accessibility to the shaft of measure, making replacements and/or required installation adjustments of the torque transducer difficult. It is demonstrated that in the absence of torque measurement, the data containing only a slow excursion of the rotor motion in response to a slight load change is sufficient to determine inertia and damping coefficients from the model. Furthermore, the generator's reactive power capability was investigated because it serves as an asset in integrated hybrid systems to meet dynamic reactive power demands, reducing the burden on the fuel cell's power electronics control in generating reactive power.

10 August 2017 in Energies
Verified
Journal Article
Open access
PDF file
SBSamuel Bayham
Samuel Bayham
RBRonald Breault
Ronald Breault
JWJustin Weber
Justin Weber
Chemical looping combustion is considered an indirect method of oxidizing a carbonaceous fuel, utilizing a metal oxide oxygen carrier to provide oxygen to the fuel. The advantage is the significantly reduced energy penalty for separating out the CO2 for reuse or sequestration in a carbon-constrained world. One of the major issues with chemical looping combustion is the cost of the oxygen carrier. Hematite ore is a proposed oxygen carrier due to its high strength and resistance to mechanical attrition, but its reactivity is rather poor compared to tailored oxygen carriers. This problem is further exacerbated by methane cracking, the subsequent deposition of carbon and the inability to transfer oxygen at a sufficient rate from the core of the particle to the surface for fuel conversion to CO2. Oxygen needs to be readily available at the surface to prevent methane cracking. The purpose of this work was to demonstrate the use of steam to overcome this issue and improve the conversion of the natural gas to CO2, as well as to provide data for computational fluid dynamics (CFD) validation. The steam will gasify the deposited carbon to promote the methane conversion. This work studies the performance of hematite ore with methane and steam mixtures in a 5 cm fluidized bed up to approximately 140 kPa. Results show an increased conversion of methane in the presence of steam (from 20–45% without steam to 60–95%) up to a certain point, where performance decreases. Adding steam allows the methane conversion to carbon dioxide to be similar to the overall methane conversion; it also helped to prevent carbon accumulation from occurring on the particle. In general, the addition of steam to the feed gas increased the methane conversion. Furthermore, the addition of steam caused the steam methane reforming reaction to form more hydrogen and carbon monoxide at higher steam and methane concentrations, which was not completely converted at higher concentrations and at these residence times.