Grain yield, ear and kernel attributes can assist to understand the performance of maize plant under different environmental conditions and can be used in the variety development process to address farmer’s preferences. These parameters are however still laborious and expensive to measure. A low-cost ear digital imaging method was developed that provides estimates of ear and kernel attributes i.e., ear number and size, kernel number and size as well as kernel weight from photos of ears harvested from field trial plots. The image processing method uses a script that runs in a batch mode on ImageJ; an open source software. Kernel weight was estimated using the total kernel number derived from the number of kernels visible on the image and the average kernel size. Data showed a good agreement in terms of accuracy and precision between ground truth measurements and data generated through image processing. Broad-sense heritability of the estimated parameters was in the range or higher than that for measured grain weight. Limitation of the method for kernel weight estimation is discussed. The method developed in this work provides an opportunity to significantly reduce the cost of selection in the breeding process, especially for resource constrained crop improvement programs and can be used to learn more about the genetic bases of grain yield determinants.

Genomic selection in maize ( Zea mays L.) has been one factor that has increased the rate of genetic gain when compared with other cereals. However, the technological foundations in maize also exist in other cereal crops that would allow prediction of hybrid performance based on general (GCA) and specific (SCA) combining abilities applied through genomic‐enabled prediction models. Further, the incorporation of genotype × environment (G × E) interaction effects present an opportunity to deploy hybrids to targeted environments. To test these concepts, a factorial mating design of elite yet divergent grain sorghum lines generated hybrids for evaluation. Inbred parents were genotyped, and markers were used to assess population structure and develop the genomic relationship matrix (GRM). Grain yield, height, and days to anthesis were collected for hybrids in replicated trials, and best linear unbiased estimates were used to train classical GCA‐SCA–based and genomic (GB) models under a hierarchical Bayesian framework. To incorporate population structure, GB was fitted using the GRM of both parents and hybrids. For GB models, G × E interaction effects were included by the Hadamard product between GRM and environments. A leave‐one‐out cross‐validation scheme was used to study the prediction capacity of models. Classical and genomic models effectively predicted hybrid performance and prediction accuracy increased by including genomic data. Genomic models effectively partitioned the variation due to GCA, SCA, and their interaction with the environment. A strategy to implement genomic selection for hybrid sorghum [ Sorghum bicolor (L.) Moench] breeding is presented herein.

Grain yield (YLD) is a function of the total biomass (BM) and of partitioning the biomass by grains, i.e., the harvest index (HI). The most critical developmental stage for their determination is the flowering time, which mainly depends on the vernalization requirement (Vrn) and photoperiod sensitivity genes (Ppd) loci. Allelic variants at the Vrn, Ppd, and earliness per se (Eps) genes of elite spring wheat genotypes included in High Biomass Association Panel (HiBAP) I and II were used to estimate their effects on the phenological stages BM, HI, and YLD. Each panel was grown for two consecutive years in Northwest Mexico. Spring alleles at Vrn-1 had the largest effect on shortening the time to anthesis, and the Ppd-insensitive allele Ppd-D1a had the most significant positive effect on YLD in both panels. In addition, alleles at TaTOE-B1 and TaFT3-B1 promoted between 3.8% and 7.6% higher YLD and 4.2% and 10.2% higher HI in HiBAP I and II, respectively. When the possible effects of the TaTOE-B1 and TaFT3-B1 alleles on the sink and source traits were explored, the favorable allele at TaTOE-B1 showed positive effects on several sink traits mainly related to grain number. The favorable alleles at TaFT3-B1 followed a different pattern, with positive effects on the traits related to grain weight. The results of this study expanded the wheat breeders’ toolbox in the quest to breed better-adapted and higher-yielding wheat cultivars.

Genomic prediction relates a set of markers to variability in observed phenotypes of cultivars and allows for the prediction of phenotypes or breeding values of genotypes on unobserved individuals. Most genomic prediction approaches predict breeding values based solely on additive effects. However, the economic value of wheat lines is not only influenced by their additive component but also encompasses a non-additive part (e.g., additive × additive epistasis interaction). In this study, genomic prediction models were implemented in three target populations of environments (TPE) in South Asia. Four models that incorporate genotype × environment interaction (G × E) and genotype × genotype (GG) were tested: Factor Analytic (FA), FA with genomic relationship matrix (FA + G), FA with epistatic relationship matrix (FA + GG), and FA with both genomic and epistatic relationship matrices (FA + G + GG). Results show that the FA + G and FA + G + GG models displayed the best and a similar performance across all tests, leading us to infer that the FA + G model effectively captures certain epistatic effects. The wheat lines tested in sites in different TPE were predicted with different precisions depending on the cross-validation employed. In general, the best prediction accuracy was obtained when some lines were observed in some sites of particular TPEs and the worse genomic prediction was observed when wheat lines were never observed in any site of one TPE.