Jinsong Chen

Dr. Jinsong Chen


Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 December 2011 in Procedia Engineering
Verified
Journal Article
Open access
JCJinsong Chen
Jinsong Chen
Ingredient and microstructure of Ni-Al2O3 nanocomposition coatings fabricated by jet electrodeposition were measured by the scanning electron microscope(SEM) with energy dispersive analyzer system (EDX), the microhardness tests were conducted on an microhardness tester. The results shows that the Ni deposited layers have nanocrystalline microstructure with average size of 50 nm. Al2O3 particles are well dispersed in layer and the particles content is up to 12.2at %. The composite coating prepared is face-centered cubic structure and represented a (2 0 0) preferential orientation. Microhardness of the coating increase and corrosion resistance of the coatings first increase then decrease with increase of Al2O3. content in coatings.

1 June 2012 in Advanced Composite Materials
Verified
Journal Article
Closed access
JCJinsong Chen
Jinsong Chen
BQBin Qiao
Bin Qiao
JYJian-Ming Yang
Jian-Ming Yang
The jet electrodeposition technology was used to prepare nano-Al2O3 nanocomposites. Effect of the additive amount of nano-Al2O3 particles and cathode current density on the nanoparticle content in composites was studied. The scanning electron microscope and X-ray diffractometer were adopted to analyze the micromorphology of the composites, research the effect of nanoparticle content in composites on the microhardness, bonding strength, and corrosion resistance. The results show that nickel deposited layer has the nanocrystalline microstructure, with the average grain size of about 40 nm; the content of nano-Al2O3 particles in the deposited layer can reach 2.5 wt%; the composite coating prepared are all face-centered cubic structure and represent a (200) preferential orientation. With the increase of Al2O3 content, the microhardness of coating will increase gradually and the bonding strength and corrosion resistance will first increase and then decrease.

23 September 2022 in Coatings
Verified
Journal Article
Open access
PDF file
WXWANG Xiaoli
WANG Xiaoli
ZZZiyi Zhao
Ziyi Zhao
JCJinsong Chen
Jinsong Chen
XZXin Zhou
Xin Zhou
YZYinjie Zong
Yinjie Zong
For the micro-milling of hard and brittle materials, to avoid crack formation, a tool with ductile milling mode is required. Composite electrodeposition technology was used to prepare a Ni–diamond coating on the surface of brass. The surface microstructure, composition and surface roughness of the coating were studied with a scanning electron microscope, X-ray diffractometer and roughness tester. The adhesion strength was studied by scratch test, the wear resistance was analyzed by wear test, and the corrosion resistance was investigated by Tafel curves and electrochemical impedance spectra (EIS). It was found that the distribution of diamond particles of the Ni–diamond coating was relatively uniform, and the content was relatively high. The internal stress of the coating prepared by the composite electrodeposition technology was very low. With the incorporation of the diamond particles, the surface roughness of the coating tended to decrease. The wear experiment showed that the wear scar diameter of the corresponding glass ball for the Ni coating was 1.775 mm and the roughness was 13.88 ± 2.811 µm, while that for the Ni–diamond coating was 2.680 mm and 8.35 ± 0.743 µm, respectively, indicating that the tool coating with uniform diamond particles had a strong ability to process workpieces with significantly improved surface quality. The particle press-in mechanism not only improved the wear resistance of the coating, but helped to prolong the service life of the tool. The results of the EIS test and Tafel curves showed that the Ni–diamond coating had a lower corrosion current, and the corrosion resistance of the coating surface was improved. The experimental results showed that the micro-diamond coating prepared by the composite electrodeposition technology had good bonding strength, low internal stress, and significantly improved wear resistance and corrosion resistance.

1 January 2011 in Advanced Composite Materials
Verified
Journal Article
Closed access
JCJinsong Chen
Jinsong Chen
YHYinhui Huang
Yinhui Huang
XGXuesong Gao
Xuesong Gao
BQBin Qiao
Bin Qiao
JYJianming Yang
Jianming Yang
YHYiqiang He
Yiqiang He
The basic principle of the formation of high-temperature Ni-base alloy reinforced by tungsten (wolfram) carbide (WC) particles using the technique of direct metal laser sintering (DMLS) was introdu...

6 December 2011 in Procedia Engineering
Verified
Journal Article
Open access
JCJinsong Chen
Jinsong Chen
The theories of jet electroforming(JEF) were introduced. The several copper specimens with simple shape were fabricated by the developed device under the optimum procession parameters. Microstructure evolution of copper layer was examined by means of the scanning electron microscopy (SEM) and x-ray diffraction (XRD). Nozzle caliber influence on electroforming rate, Formed precision, sanning interval were studied, The result shows that nozzle caliber has basal the linear relation with the electroforming rate, the electroforming rate increases with increasing nozzle caliber; nozzle caliber has great effects on the precision of electroforming spot, the well precision of electroforming spot can be gained with the small nozzle caliber.

23 November 2012 in Transactions of the Indian Institute of Metals
Verified
Journal Article
Closed access
PDF file
JCJinsong Chen
Jinsong Chen
YJYang Jianming
Yang Jianming
QBQiao Bin
Qiao Bin