Mohankumar S

Mr. Mohankumar S


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 May 2023 in Heliyon
Verified
Journal Article
Open access
RVR. Venkatesh
R. Venkatesh
SBSuhas Ballal
Suhas Ballal
AKA. Mohana Krishnan
A. Mohana Krishnan
SPS. Prabagaran
S. Prabagaran
MSMohankumar S
Mohankumar S
ERElangomathavan Ramaraj
Elangomathavan Ramaraj
Natural fiber-reinforced polymer matrix composites are gathering significance in future trend applications such as automotive, aerospace, sport, and other engineering applications due to their superior enhanced mechanical, wear, and thermal properties. Compared to synthetic fiber, natural fiber is low adhesive and flexural strength properties. The research aims to synthesize the epoxy hybrid composites by utilizing the silane (pH = 4) treated Kenaf (KF) and sisal fiber (SF) as layering by uni, bi, and multi-unidirectional via hand layup techniques. Thirteen composite samples have been prepared by three-layer formation adopted with different weight ratios of E/KF/SF such as 100E/0KF/0SF, 70E/30KF/0SF, 70E/0KF/30SF, 70E/20KF/10SF, and 70E/10KF/20SF respectively. The effect of layer formation on the tensile, flexural, and impact strength of composites is studied by ASTM D638, D790, and D256 standards. The unidirectional fiber layer formed (sample 5) 70E/10KF/20SF composite is found maximum tensile and flexural strength of 57.9 ± 1.2 MPa and 78.65 ± 1.8 MPa. This composite is subjected to wear studies by pin-on-disc wear apparatus configured with a hardened grey cast-iron plate under an applied load of 10, 20, 30, and 40 N at different sliding velocities of 0.1, 0.3, 0.5, and 0.7 m/s. The wear rate of the sample progressively increases with increasing load and sliding speed of the composite. The minimum wear rate of 0.012 mg/min (sample 4) is found on 7.6 N frictional force at 0.1 m/s sliding speed. Moreover, sample 4 at a high velocity of 0.7 m/s with a low load (10 N) shows a wear rate of 0.034 mg/min. The wear-worn surface is examined and found adhesive and abrasive wear on a high frictional force of 18.54 N at 0.7 m/s. The enhanced mechanical and wear behavior of sample 5 is recommended for automotive seat frame applications.

3 June 2025 in Materials Testing
Verified
Journal Article
Closed access
MSMohankumar S
Mohankumar S
NRNaveen Kumar Raju
Naveen Kumar Raju
RRRajasekar Rathanasamy
Rajasekar Rathanasamy
GKGobinath Velu Kaliyannan
Gobinath Velu Kaliyannan
The current work examines how flyash reinforcement, SiCp, and B4Cp affect the tribological and mechanical characteristics of composites made of aluminum 359. Stir casting was used to create composite samples of B4Cp, SiCp and flyash reinforced Al 359. The composites’ hardness, tensile behavior, and wear behavior were examined and contrasted with a control sample. Due to the ceramic phase, the B4Cp, SiCp particles, and flyash reinforced Al 359 matrix are harder than the base matrix. When B4Cp, SiCp and flyash are added to the base matrix up to 20 wt.%, the coefficient of friction increases significantly. Wear examinations were carried out on specimens under a variety of stress situations, and then five different wear processes listed here (wear groove, abrasion, delamination, oxidation, and plastic deformation) were explored. The finding of the abrasion test show that B4Cp, SiCp and flyash enhanced composites have improved wear resistance when compared to a control specimen.