Steer-by-wire (SBW) systems provide significant benefits to classical vehicles, and are indispensable for fully autonomous vehicles (AVs). A backup (emergency) strategy is needed to steer a AV equipped with SBW to safety if its steering actuator fails completely. Differential drive assisted steering (DDAS), which uses torque vectoring (TV) to steer a vehicle in the absence of a steering actuator, has been proposed as a backup strategy for SBW systems. However, vehicle stability control (VSC) – a required feature in most modern vehicles – also relies on torque vectoring to assist vehicles in maintaining stability. In this paper, it is shown through stability analyses on a linearized vehicle model that VSC enhances the stability of a AV equipped with a fully functional SBW system. Conversely, when combined with DDAS as a backup steering strategy for a failed SBW system, VSC typically deteriorates stability. Thus, the benefits of VSC in ensuring stability cannot be taken for granted for AVs, e.g., by designing it as a decoupled controller added on to DDAS. Instead, VSC and DDAS must be designed in an integrated manner to guarantee stability. To support this finding, simulations are conducted where a nonlinear AV model with either SBW or DDAS – both combined with VSC and implemented via model predictive control – are used to carry out an ISO-standard double lane change test at 80 km/h. Using the SBW system, the AV passes the test, both with VSC decoupled from and integrated with the SBW system. However, in the case of SBW failure, the AV with VSC decoupled from DDAS fails the test, while that with VSC integrated with DDAS completes the test successfully.
In rubber-wheeled road vehicles, the mechanical connection between steering wheel and front wheels provides steering-related feedback to the driver. The torque fed back to the driver through the steering linkages and steering wheel, which is called steering feel, helps the driver in controlling the vehicle. The torque feedback is reproduced via artificial methods in steer-by-wire systems due to the lack of mechanical connection. In this work, in order to minimize the physical workload and the lateral acceleration under the consideration of handling performance, optimization of a hysteresis-based steering feel has been studied. A 2-degree-of-freedom bicycle model based on the magic formula tire model has been used for simulations and hardware-in-the-loop experiments. A mathematical model is proposed in order to create an adaptive model-based optimization of the hysteresis parameters simultaneously while driving. A hardware-in-the-loop experimental setup has been used for the driving tests. The weave and the double-lane change tests have been performed with different drivers in order to demonstrate and quantify the optimization methods that are presented in this work.
30 July 2020 in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
It is anticipated that passengers in autonomous vehicles will be more occupied with in-vehicle activities. Loss of the authority on driving and engaging in non-driving tasks could cause lower predictability of car motions. This decrease in predictability is expected to increase the sensitivity to carsickness. It appears that it is crucial to develop controllers for autonomous driving with the capability of improving passenger comfort by reducing carsickness. In this regard, it can be asked how the motion variables can be used for the minimization of a carsickness-related measure, while the vehicle is required to follow a given path. In this study, an optimal control approach is being proposed to minimize a quantitative measure of carsickness. In order to address carsickness during autonomous maneuvers, the well-known motion sickness dose value formulation in ISO 2631-1 is augmented with horizontal direction motion components to define a performance measure. The performance measure includes the motion sensed in vestibular system rather than the motion occurring in the vehicle itself. Therefore, mathematical model of the vestibular system is included in the design of controller. Effects of acceleration and jerk are included in performance measure simultaneously. Control oriented linear parameter varying vehicle model is developed to design the path following controller. By means of simulation studies in which path following control is implemented, motion sickness dose values of the controlled vehicle are examined. It is shown by a regular lane change test at various speeds that the proposed controller, which seeks the minimization of the motion sickness dose value, achieves a reduction of the acceleration and jerk felt by a passenger, while the vehicle follows the given path.
Objective of this work is to design and manufacture a model satellite named Vecihi that is able to perform some of the basic tasks that artificial satellites perform. The satellite is developed under the rules of CanSat Competition 2013, which aims to promote innovative space solutions and to improve the current systems. The Vecihi satellite designed around budgetary, dimensional, and mass requirements as set in the competition guidelines, while carrying and landing its payload successfully.
28 March 2017 in SAE International Journal of Transportation Safety
Electric Power Assisted Steering (EPAS) is widely adopted in modern vehicles to reduce steering effort. It is probable that some EPAS systems will experience a shutdown due to reliability issues stemming from electrical and/or electronic components. In the event of EPAS failure, power assist becomes unavailable and the steering system reverts to a fully manual state, leading to excessive steering torque demands from the driver to maneuver the vehicle at lower speeds, i.e., under 30 mph. This situation has resulted in dozens of reported crashes and several OEM safety recalls in the past few years. Inspired by recent work which utilizes independent driving torque of in-wheel-motor vehicles to reduce steering torque, this paper proposes the use of Differential Braking Assisted Steering (DBAS) to alleviate steep increases in steering torque upon EPAS failure. DBAS requires software upgrades with minimal hardware modification to EPAS, which is preferable for a backup system. A preliminary evaluation of DBAS is carried out using simulations in CarSim. Results show that DBAS reduces steering torque to similar levels as EPAS in all of the steady state, transient and urban driving scenarios investigated. The results also show that DBAS triggers vehicle speed reduction and oversteer, the latter of which is in conflict with Electronic Stability Control (ESC) which is designed to inherently prevent oversteer. Since ESC is typically crucial at higher speeds, this conflict can be avoided by employing DBAS only at lower speeds where steering assist is most needed. This paper motivates further study of DBAS for emergency safety in the event of EPAS failure.
1 July 2018 in International Journal of Advanced Robotic Systems
Tactile sensors are commonly a coordinated group of receptors forming a matrix array meant to measure force or pressure similar to the human skin. Optic-based tactile sensors are flexible, sensitive, and fast; however, the human fingertip’s spatial resolution, which can be regarded as the desired spatial resolution, still could not be reached because of their bulky nature. This article proposes a novel and patented optic-based tactile sensor design, in which fiber optic cables are used to increase the number of sensory receptors per square centimeter. The proposed human-like high-resolution tactile sensor design is based on simple optics and image processing techniques, and it enables high spatial resolution and easy data acquisition at low cost. This design proposes using the change in the intesity of the light occured due to the deformation on contact/measurement surface. The main idea is using fiber optic cables as the afferents of the human physiology which can have 9 µm diameters for both delivering and receiving light beams. The variation of the light intensity enters sequent mathematical models as the input, then, the displacement, the force, and the pressure data are evaluated as the outputs. A prototype tactile sensor is manufactured with 1-mm spatial and 0.61-kPa pressure measurement resolution with 0–15.6 N/cm 2 at 30 Hz sampling frequency. Experimental studies with different scenarios are conducted to demonstrate how this state-of-the-art design worked and to evaluate its performance. The overall accuracy of the first prototype, based on different scenarios, is calculated as 93%. This performance is regarded as promising for further developments and applications such as grasp control or haptics.