The global production of fossil-based plastics has reached critical levels, and their substitution with bio-based polymers is an urgent requirement. Poly(3-hydroxybutyrate) (PHB) is a biopolymer that can be produced via microbial cultivation, but efficient microorganisms and low-cost substrates are required. Halomonas boliviensis LC1, a moderately halophilic bacterium, is an effective PHB producer, and hydrolysates of the residual stalks of quinoa (Chenopodium quinoa Willd.) can be considered a cheap source of sugars for microbial fermentation processes in quinoa-producing countries. In this study, H. boliviensis LC1 was adapted to a cellulosic hydrolysate of quinoa stalks obtained via acid-catalyzed hydrothermal pretreatment and enzymatic saccharification. The adapted strain was cultivated in hydrolysates and synthetic media, each of them with two different initial concentrations of glucose. Cell growth, glucose consumption, and PHB formation during cultivation were assessed. The cultivation results showed an initial lag in microbial growth and glucose consumption in the quinoa hydrolysates compared to cultivation in synthetic medium, but after 33 h, the values were comparable for all media. Cultivation in hydrolysates with an initial glucose concentration of 15 g/L resulted in a higher glucose consumption rate (0.15 g/(L h) vs. 0.14 g/(L h)) and volumetric productivity of PHB (14.02 mg/(L h) vs. 10.89 mg/(L h)) than cultivation in hydrolysates with 20 g/L as the initial glucose concentration. During most of the cultivation time, the PHB yield on initial glucose was higher for cultivation in synthetic medium than in hydrolysates. The produced PHBs were characterized using advanced analytical techniques, such as high-performance size-exclusion chromatography (HPSEC), Fourier transform infrared (FTIR) spectroscopy, ¹H nuclear magnetic resonance (NMR) spectroscopy, scanning electron microscopy (SEM), X-ray diffraction (XRD), and thermogravimetric analysis (TGA). HPSEC revealed that the molecular weight of PHB produced in the cellulosic hydrolysate was lower than that of PHB produced in synthetic medium. TGA showed higher thermal stability for PHB produced in synthetic medium than for that produced in the hydrolysate. The results of the other characterization techniques displayed comparable features for both PHB samples. The presented results show the feasibility of producing PHB from quinoa stalks with H. boliviensis.

Zirconia is known for its high strength but lacking translucency. Recently, a new type of high translucent zirconia, 5 mol% yttria partially stabilized zirconia (5Y-PSZ), with a larger fraction of cubic zirconia phase has become commercially available. However, the resistance to aging of these commercially available zirconia materials is not yet fully established. Purpose: The aim of the present study was to analyze the effects of artificial aging on surface roughness, transparency, phase transformation and biaxial flexural strength of two 5Y-PSZ products, DD cubeX² and Prettau Anterior. Materials and methods: The artificial aging was performed in an autoclave under 2 bars of pressure at 134 °C for 10 hours, which is estimated to correspond to 30–40 years in vivo. Artificial aging for 10 hours had no significant effect on surface roughness, transparency, or phase transformation for either of the tested materials. Results: DD cubeX² had higher mean flexural strength than Prettau Anterior both before and after artificial aging for 10 hours (p < .05). DD cubeX² showed, however, a significant reduction in flexural strength after artificial aging (p < .05), whereas Prettau Anterior showed a slight increase in flexural strength after artificial aging but not at a significant level. Conclusion: Within the limitation of the present study, both DD cubeX² and Prettau Anterior seems to be relatively resistant to aging. However, a wider range of measured flexural strength indicated that Prettau Anterior probably is a less stable material than DD cubeX², which also means that the flexural strength of DD cubeX² could be more predictable.

Quicklime is produced through the thermal processing of limestone in industrial kilns. During quarry operations, fine particulate quarry dust adheres to limestone lump surfaces, increasing the bulk concentration of impurities in limestone products. During thermal processing in a kiln, impurities such as Si, Mg, Al, Fe, and Mn react with Ca, reducing quicklime product quality. Which reactant phases are formed, and the extent to which these result in a reduction in quality, has not been extensively investigated. The present study investigated as-received and manually washed limestone product samples from two operational quarries using elemental compositions and a developed predictive multi-component chemical equilibrium model to obtain global phase diagrams for 1000–1500 °C, corresponding to the high-temperature zone of a lime kiln, identifying phases expected to be formed in quicklime during thermal processing. The results suggest that impurities found on the surface of the lime kiln limestone feed reduce the main quality parameter of the quicklime products, i.e., calcium oxide, CaO (s), content by 0.8–1.5 wt.% for the investigated materials. The results also show that, in addition to the effect of impurities, the quantity of CaO (s) varies greatly with temperature. More impurities result in more variation and a greater need for accurate temperature control of the kiln, where keeping the temperature below approximately 1300 °C, that of Hatrurite formation, is necessary for a product with higher CaO (s).