Water electrolysis is a compelling method for the production of environmentally friendly hydrogen, minimizing carbon emissions. The electrolysis of water heavily relies on an effective and steady oxygen evolution reaction (OER) taking place at the anode. Herein, we introduce a highly promising catalyst for OER called CoSe2@NiFeOOH arrays, which are supported on nickel foam. This catalyst, referred to as CoSe2@NiFeOOH/NF, is fabricated through a two-step process involving the selenidation of a Co-based porous metal organic framework and subsequent electrochemical deposition on nickel foam. The CoSe2@NiFeOOH/NF catalyst demonstrates outstanding activity for the OER in an alkaline electrolyte. It exhibits a low overpotential (η) of 254 mV at 100 mA cm−2, a small Tafel slope of 73 mV dec−1, and excellent high stability. The good performance of CoSe2@NiFeOOH/NF can be attributed to the combination of the high conductivity of the inner layer and the synergistic effect between CoSe2 and NiFeOOH. This study offers an effective method for the fabrication of highly efficient catalysts for an OER.
Currently, the process of an acidic oxygen evolution reaction (OER) necessitates the use of Iridium dioxygen (IrO2), which is both expensive and incredibly scarce on Earth. Ruthenium dioxygen (RuO2) offers high activity for acidic OERs and presents a potential substitution for IrO2. Nevertheless, its practical application is hindered by its relatively poor stability. In this study, we have developed Mn–doped RuO2 (Mn–RuO2) nanoarrays that are anchored on a titanium (Ti) mesh utilizing a two–step methodology involving the preparation of MnO2 nanoarrays followed by a subsequent Ru exchange and annealing process. By precisely optimizing the annealing temperature, we have managed to attain a remarkably low overpotential of 217 mV at 10 mA cm−2 in a 0.5 M H2SO4 solution. The enhanced catalytic activity of our Mn–RuO2 nanoarrays can be attributed to the electronic modification brought about by the high exposure of active sites, Mn dopant, efficient mass transfer, as well as the efficient transfer of electrons between the Ti mesh and the catalyst arrays. Furthermore, these self–supported Mn–RuO2 nanoarrays demonstrated excellent long–term stability throughout a chronoamperometry test lasting for 100 h, with no discernible changes observed in the Ru chemical states.
Asymmetric nickel oxyhydroxide (NiOOH) possesses multi-OH and O active sites on different surfaces, (001) and (001̄), which possibly causes a complicated catalytic process.
On-site hydrogen generation from ammonia decomposition is a promising technology to address the challenges of direct transportation and storage of hydrogen. The main problems with the existing support materials for ammonia decomposition catalysts are their high cost and time-consuming preparation process. In this work, ammonia decomposition catalysts consisting of in situ-formed nano-Ru particles supported on a naturally abundant mineral fiber, attapulgite (ATP), were proposed and studied. Also, 1 wt.% Ru was uniformly dispersed and anchored onto the surface of ATP fibers via the chemical method. We found that the calcination temperatures of the ATP support before the deposition of Ru resulted in little difference in catalytic performance, while the calcination temperatures of the 1Ru/ATP precursor were found to significantly influence the catalytic performance. The prepared 1 wt.% Ru/ATP catalyst (1Ru/ATP) without calcination achieved an ammonia conversion efficiency of 51% at 500 °C and nearly 100% at 600 °C, with the flow rate of NH3 being 10 sccm (standard cubic centimeter per minute). A 150 h continuous test at 600 °C showed that the 1Ru/ATP catalyst exhibited good stability with a degradation rate of about 0.01% h−1. The 1Ru/ATP catalyst was integrated with proton ceramic fuel cells (PCFCs). We reported that PCFCs at 650 °C offered 433 mW cm−2 under H2 fuel and 398 mW cm−2 under cracked NH3 fuel. The overall results suggest low-level Ru-loaded ATP could be an attractive, low-cost, and efficient ammonia decomposition catalyst for hydrogen production.
Bioinspired electrothermally activated polymer gel systems with synergistic fluorescence-colour/3D shape changing properties are developed for rewritable and programmable information displays.
The structural evolution of CoSe 2 from 2D to 1D is achieved through the precise regulation of sulfur. The obtained S-CoSe 2 NWs can efficiently mobilize nitrate reduction to ammonia in temperate environments.