For the preparation of activated carbon papers (APCs) as supercapacitor electrodes, impurity substances were removed from rice husks, before carbonization and various activation temperature treatments, to optimize electro chemical efficiency. The porosities and electrochemical performances of the ACPs depended strongly on activation temperature: The specific surface area increased from 202.92 (500 °C) to 2158.48 m2 g−1 (1100 °C). XRD and Raman analyses revealed that ACP graphitization also increased with the activation temperature. For activation at 1100 °C, the maximum specific capacitance was 255 F g−1, and over 92% of its capacitance was retained after 2000 cycles.
Carbon foam was prepared from carboxymethyl cellulose (CMC) and Ag, Al and carbon nanotubes (CNTs), and graphene was added to the foam individually, to investigate the enhancement effects on the thermal conductivity. In addition, we used the vacuum method to impregnate erythritol of the phase change material (PCM) into the carbon foam samples to maximize the latent heat and minimize the latent heat loss during thermal cycling. Carbon foams containing Ag (CF-Ag), Al (CF-Al), CNT (CF-CNT) and graphene (CF-G) showed higher thermal conductivity than the carbon foam without any nano thermal conducting materials (CF). From the variations in temperature with time, erythritol added to CF, CF-Ag, CF-Al, CF-CNT, and CF-G was observed to decrease the time required to reach the phase change temperature when compared with pure erythritol. Among them, erythritol added to CF-G had the fastest phase change temperature, and this was related to the fact that this material had the highest thermal conductivity of the carbon foams used in this study. According to differential scanning calorimetry (DSC) analyses, the materials in which erythritol was added (CF, CF-Ag, CF-Al, CF-CNT, and CF-G) showed lower latent heat values than pure erythritol, as a result of their supplementation with carbon foam. However, the latent heat loss of these supplemented materials was less than that of pure erythritol during thermal cycling tests because of capillary and surface tension forces.
Waste wood contains large amounts of cellulose fibers that have outstanding mechanical properties. These fibers can be recycled and converted into highly valuable materials of waste wood. In this study, waste wood cellulose fiber/graphene nanoplatelet (WWCF/GnP) papers were prepared according to the WWCF and GnP contents. Subsequently, the WWCF/GnP papers were varyingly carbonized for their application as electromagnetic interference (EMI) shielding materials such as state-of-the-art electronic equipment malfunction prevention, chip-level microsystem, and micro intersystem noise suppression/reduction. The increase in the GnP content and carbonization temperature enhanced electrical conductivity, thereby generating a greater EMI shielding effectiveness (EMI SE) in the high-frequency X-band. Additionally, the thickness of the WWCF/GnP carbon papers improved the electrical conductivity and EMI SE values. The electrical conductivity of the WWCF/GnP-15 carbon paper obtained at carbonization temperature of 1300 °C was approximately 5.86 S/m, leading to an EMI SE value of 43 decibels (dB) at 10.5 GHz for one sheet. Furthermore, overlapping of the three sheets increased the electrical conductivity to 7.02 S/m, leading to an EMI SE value of 72.5 dB at 10.5 GHz. Thus, we isolated WWCFs, without completely removing contaminants, for recycling and converting them into highly valuable EMI shielding materials.
This work investigates the possibility of isolating cellulose nanofibers from pulps of tall goldenrod plant, which are invasive plants in Korea, by a convenient method, without strong acids or high-pressure homogenization, using electron beam irradiation (EBI). The obtained cellulose nanofibers were characterized by scanning electron microscopy (SEM), ultraviolet–visible (UV–vis) spectroscopy, X-ray diffraction (XRD), thermogravimetric analysis (TGA), and in terms of their mechanical properties. SEM showed that the initially isolated 10-μm-diameter cellulose fibers became more finely separated with increasing EBI dose, and that cellulose fibers treated with 300 kGy of EBI were separated into long cellulose nanofibers of around 160 nm in diameter. In addition, the paper samples prepared from more finely separated fibers generated by using higher doses of EBI had enhanced UV–vis transmittance. Via the XRD analysis, we observed that cellulose I in the EBI-treated cellulose fibers were gradually converted into a different type of cellulose similar to cellulose type II, as the EBI dose increased. Meanwhile, the TGA demonstrated that the finely separated cellulose fibers observed after administering the high EBI dose had lowered thermal stability due to the reduction of cellulose I but higher char yield. In addition, tensile strengths of paper samples increased with decreasing the diameters of their constituent fibers that result from the different EBI doses used in the preparation of the paper pulp.
To transform tall goldenrods, which are invasive alien plant that destroy the ecosystem of South Korea, into useful materials, cellulose fibers isolated from tall goldenrods are applied as EMI shielding materials in this study. The obtained cellulose fibers were blended with CNTs, which were used as additives, to improve the electrical conductivity. TGCF/CNT papers prepared using a facile paper manufacturing process with various weight percent ratios and thickness were carbonized at high temperatures and investigated as EMI shielding materials. The increase in the carbonization temperature, thickness, and CNT content enhanced the electrical conductivity and EMI SE of TGCF/CNT carbon papers. TGCF/CNT-15 papers, with approximately 4.5 mm of thickness, carbonized at 1300 °C exhibited the highest electrical conductivity of 6.35 S cm−1, indicating an EMI SE of approximately 62 dB at 1.6 GHz of the low frequency band. Additionally, the obtained TGCF/CNT carbon papers were flexible and could be bent and wound without breaking.
Carbon fibers, which act as reinforcements in many applications, are often obtained from polyacrylonitrile (PAN). However, their production is expensive and results in waste problems. Therefore, we focused on producing carbon fibers from lyocell, a cellulose-based material, and analyzed the effects of the process parameters on their mechanical properties and carbon yields. Lyocell was initially grafted with polyacrylamide (PAM) via electron-beam irradiation (EBI) and was subsequently stabilized and carbonized. Thermal analysis showed that PAM grafting increased the carbon yields to 20% at 1000 °C when compared to that of raw lyocell, which degraded completely at about 600 °C. Stabilization further increased this yield to 55%. The morphology of the produced carbon fibers was highly dependent on PAM concentration, with fibers obtained at concentrations ≤0.5 wt.% exhibiting clear, rigid, and round cross-sections with smooth surfaces, whereas fibers obtained from 2 and 4 wt.% showed peeling surfaces and attachment between individual fibers due to high viscosity of PAM. These features affected the mechanical properties of the fibers. In this study, carbon fibers of the highest tensile strength (1.39 GPa) were produced with 0.5 wt.% PAM, thereby establishing the feasibility of using EBI-induced PAM grafting on lyocell fabrics to produce high-performance carbon fibers with good yields.