Perovskite solar cells (PSCs) have made incredibly fast progress in the past years, with the efficiency approaching 26%, which is comparable to those of the best silicon solar cells. One of the features of PSCs that make them stand out among all photovoltaics (PVs) is their high open-circuit voltage (VOC) although they are made by solution processes. Compared to other solution-processed PVs such as organic photovoltaics and dye-sensitized solar cells, and vacuum-processed PVs like CdTe and CIGS, the loss in VOC caused by non-radiative recombination in the case of PSCs is considerably low, which is even as low as that observed for vacuum-processed Si. The defect-tolerant nature of perovskites helps in preventing non-radiative recombination and therefore yields high VOC in PSCs. By comparing the achieved performance with the Shockley–Queisser (S–Q) limits, it can be determined that while the photocurrent of PSCs reaches almost the theoretical limit, there is still room to improve the VOC, especially in the case of all-inorganic and tin-based perovskites. Hence, improving the VOC becomes critical for promoting device efficiency further. In this review paper, we focus our discussion on the recent development of VOC of PSCs by beginning with a theoretical review highlighting the critical role of VOC enhancement and the necessity of non-radiative recombination suppression for device performance improvement. As the recombination both in the bulk of the perovskite and on the surface/interfaces with charge transport layers is important, different methods depending on the perovskite composition and the nature of the electron transport layer (ETL) and hole transport material (HTM) have been developed to minimize recombination in the perovskite and at the interfaces. We provide a comprehensive review of different reported strategies for reducing undesirable recombination in the perovskite film and at the interfaces, by dividing our discussion into four parts based on the light absorbers used: organic–inorganic hybrid perovskites, all-inorganic perovskites, tin-based perovskites, and bismuth-based perovskites (analogs). Finally, a summary with an outlook on how reducing perovskite film defects and developing more suitable charge transport layers can further promote the VOC and expand the practical application prospects of PSCs is presented.
Global demand for plastics has increased steadily alongside industrial development. Despite their versatility and convenience, environmental pollution caused by plastics are a major issue. With a reduction in the market size of plastics being seemingly impossible, bioplastics may become key to tackle this issue. Among a wide range of sources of bioplastics, microalgae have come into the limelight. While abundant and valuable components in microalgae have the potential to replace preexisting plastics, complex processes and low cost performances have prevented them from entering the market. In this study, we examined techniques for biocomposites in which polymers are blended with microalgae. We focused on microalgae-based biocomposite blending processed from the perspective of functionality and cost performance.
30 May 2025 in Advances in Industrial and Engineering Chemistry
Tin dioxide (SnO2) is widely used as an electron transport layer (ETL) in perovskite solar cells (PSCs) due to its high electron mobility and stability. While atomic layer deposition (ALD) enables the formation of uniform and defect-free SnO2 films, its direct contact with perovskite leads to energy level mismatch and charge recombination, limiting device performance. In this study, we systematically investigate the role of ALD-SnO2 in PSCs and reveal that its direct interface with perovskite induces severe energy loss rather than efficient charge transport. To address this, we examine a double-layer ETL architecture, where a spin-coated SnO2 nanoparticle layer is deposited on ALD-SnO2. Optical and morphological analyses confirm that ALD-SnO2 alone causes charge trapping, while ALD + SC improves charge extraction and interfacial quality. As a result, PSCs with ALD + SC achieve a power conversion efficiency (PCE) exceeding 22%, significantly outperforming ALD-only and spin-coated-only SnO2 configurations.
Microalgae-based biocomposites are gaining traction as ecofriendly and cost-effective alternatives to conventional petroleum-based plastics. However, achieving a homogeneous dispersion of microalgae within a biocomposite matrix remains a challenge. In this study, we investigated the effect of the size of dried microalgae (Chlorella sp.) on the quality of biocomposites. Ball milling, a mechanical grinding process, was used to control the size of the pretreated dried microalgae. Our results demonstrate that the microalgae size strongly depends on the total weight of the stainless-steel balls, rather than the number of balls used in the milling process. Poly(ethylene-vinyl acetate) (EVA), with functional groups resembling those of Chlorella sp., was incorporated into the ball-milled microalgae to produce homogeneous biocomposites. Smaller Chlorella sp. particles improved the ratio of microalgae and the mechanical properties of the biocomposites. Dried Chlorella sp. particles up to 161.43 μm, which were 72.84% smaller than the untreated microalgae, were obtained after 6 h of ball milling using 3/8-inch balls. This enabled the production of biocomposites with 60 wt.% microalgae and 61.02% of the tensile strength of pure EVA, comparable to traditional polymers. Our findings suggest that controlling the microalgae size through ball milling can improve the quality of microalgae-based biocomposites.