The rational structural design of polycrystalline diamond compact (PDC) cutters effectively enhances the performance of drill bits in rock fragmentation and extends their service life. Inspired by bionics, a bionic PDC cutter was designed, taking the mole claw toe, shark tooth, and microscopic biomaterial structures as the bionic prototypes. To verify its rock-breaking effectiveness, the finite element method was employed to compare the rock-breaking processes of the bionic cutter, triangular prism cutter, and axe cutter. The study also investigated the influence of different back rake angles, cutting depths, arc radii, and hydrostatic pressures on rock breaking using the bionic cutter. Prior to this, the accuracy of the finite element model was validated through laboratory tests. Subsequently, a drill bit incorporating all three types of cutters was constructed, and simulations of rock breaking were conducted on a full-sized drill bit. The results demonstrate that the bionic cutter exhibits superior load concentration on the rock compared to the triangular prism cutter and the axe cutter. Additionally, its arc structure facilitates the “shoveling” of the rock, making it more susceptible to breakage under tensile stress. As a result, the efficiency of the bionic cutter surpasses that of the triangular prism and axe cutters. Similarly, it exhibits minimal fluctuations and values in cutting force. As the back rake angle and cutting depth increase, the MSE and cutting force of all three cutters also increase. However, the bionic cutter consistently maintains the lowest MSE and cutting force, confirming the superiority of its bionic structural design. The MSE and cutting force of the bionic cutter fluctuate with the increase of the arc radius, and the optimal arc radius falls within the simulation range, between 21 mm and 23 mm. Compared to the other two types of cutters, bionic cutters possess a unique structure that allows for better release of internal stress within the rock, thereby ensuring higher efficiency in rock-breaking, particularly in deep geological formations. The rock breaking simulation results of full-sized drill bits show that the use of a bionic cutter can improve the drill bit’s ability to penetrate the formation, reduce the possibility of drill bit bounce during the rock breaking process, prevent the occurrence of stick-slip, improve the drilling stability, effectively improve the efficiency and service life of the drill bit during the rock breaking process, and reduce the drilling cost. It is concluded that the research results of bionic PDC cutters are helpful to the development of high-performance drill bits and the reduction of drilling costs.

As the depth of petroleum drilling increases, the strata environment becomes more complex. The efficiency and lifespan of Polycrystalline Diamond Compact (PDC) drill bits fail to meet current drilling demands. However, the structure and arrangement of PDC cutters are valuable determinants of drilling efficiency, although related research still has gaps and deficiencies. This study focuses on PDC cutters in axe, triangular prism, and circular forms. It establishes an inhomogeneous granite model based on the actual measurements of granite and verifies the accuracy of this model through uniaxial compression simulation. Finite element models of three types of cutters in various combination schemes are constructed to examine rock-breaking effects, with the best scheme optimized using Box-Behnken response surface methodology. The rock-breaking process of the optimal PDC drill bit layout has been compared to that of a single cutter bit. Field drilling has demonstrated the effectiveness of a mixed cutter arrangement. The results show that the inhomogeneous granite model can be trusted. The optimal arrangement involves axe cutters in the front row and an alternate arrangement of triangular prism cutters and axe cutters in the back row. The optimal lateral and longitudinal distances for the triangular cutters from the front row of axe cutters are 10 mm and 7 mm, respectively, while those for the back row of axe cutters from the front row are 10.06 mm and 7 mm, respectively. The ROP standard deviation in the drilling process of mixed cutter bits decreases by 53.06% and 43.08% compared to axe and triangular prism cutter bits, respectively. The drilling efficiency increases by 16.8% and 16.6%, respectively, demonstrating higher efficiency and stability. Field drilling results indicate that a mixed cutter bit increases efficiency by 23.5% compared to a bit with only triangular prism cutters. This study posits that research on the combination schemes and parameters of PDC cutters can significantly enhance drilling efficiency, thereby reducing the drilling cycle and costs.

The cutter structure and layout scheme of PDC (Polycrystalline Diamond Compact) bits are important factors in improving efficiency. To further improve the drilling efficiency of PDC bits, axe, triangular prism, and cylindrical PDC cutters were used as research objects. Based on the measured granite data, a finite element model of non-homogeneous granite was established and verified by uniaxial compression simulation. The rock-breaking process of different cutter combination schemes was compared using the finite element method, and the parameters in the best scheme were optimized using the Box-Behnken response surface method. The results show that the constructed model of non-homogeneous granite is consistent with the stress-strain relationship of real granite and is reliable. The axe PDC cutter is more aggressive than the other two cutters and is more suitable for the front row of the bit blade tooth arrangement, while the triangular prism cutter is the second most aggressive and is suitable for the rear row of tooth arrangement, and the best combination scheme is the front row of axe cutter and the rear row of triangular prism cutter arranged alternately with the axe cutter. The optimal transverse and longitudinal distances of the optimized triangular prism cutter from the front axe cutter are 10mm and 7mm, and the optimal transverse and longitudinal distances of the rear axe cutter from the front cutter are 10.06mm and 7mm. The drilling speed is more stable during drilling and the PDC bit with mixed tooth arrangement has 16.8% and 16.6% higher rate of penetration(ROP) compared with the bit with single axe cutter and triangular prism cutter, and the drilling speed is more stable during working, which can effectively improve the rock breaking efficiency of the PDC bit. The field application proves that the bit with mixed cutter arrangement is easier to break the complex formations, with more stable ROP and better efficiency. The study can provide theoretical support for the cutter layout of the PDC bit.

Geothermal energy, recognized as a clean energy source, has attracted widespread attention for its extraction. However, it is located in deep and complex geological formations, presenting a significant challenge to the drilling operations of existing Polycrystalline Diamond Compact (PDC) drill bits. To further understand the rock-breaking mechanism of PDC cutters in deep geological formations and improve rock-breaking efficiency, a finite element model employing the cohesive zone method was developed for a saddle-shaped PDC cutter (SC). This model was validated against experimental simulations, proving its capability to capture real rock crack initiation during the simulation process accurately. By analyzing the formation of cracks under cutting forces, the SC’s rock-breaking mechanism was explored and compared with conventional cutters (CCs), clarifying its advantages. Additionally, the model analyzed the effects of different confined pressures, back rake angles, and structural parameters on crack formation in SC rock-breaking, highlighting directions for structural optimization. Full-scale drill bit rock-breaking simulations were conducted to verify the effectiveness and optimization of single cutter usage. The results indicated that the total number of cracks and the generation of tensile cracks determine the rock-breaking efficiency of the cutter. A lower total number of cracks and a higher proportion of tensile cracks lead to better rock-breaking performances. Due to its unique ridged and curved structure, the SC can generate concentrated and tensile stresses on the rock more effectively, resulting in fewer total cracks and a higher proportion of tensile cracks. The increase in confined pressure suppresses the generation of tensile cracks during rock-breaking, dispersing the rock-breaking energy, increasing the total number of cracks, and reducing rock-breaking efficiency. However, under the same conditions, using SC can effectively address these issues and enhance efficiency. For deep formation drilling, a back rake angle range of 15° to 20° is recommended for SC. The arc radius significantly impacts the SC’s tensile cracks and total number of cracks, with a recommended arc radius range of 50 mm to 60 mm, and the SC structure could be modified from an arc to a straight line and back to an arc. The results contribute to enhancing the efficiency of deep drilling and theoretical research on drill bits.