In March 2020, an all-solid-state dual-wavelength narrow-band lidar system was deployed. A total of 226 nights spanning from March 2020 to July 2022 were employed in order to investigate the seasonal variations of calcium atoms and ions in the mesosphere over Beijing (40.41°N, 116.01°E). The Ca⁺ layer shows general annual variation, while a semiannual variation is observed on the Ca layer. The calcium atomic column densities ranged from 2.0 × 10⁶ to 1.1 × 10⁸ cm⁻², and the calcium ion column densities ranged from 1.6 × 10⁶ to 4.2 × 10⁸ cm⁻². The mean centroid heights of Ca⁺ and Ca are 98.6 km and 93.0 km, respectively, and the centroid heights of Ca⁺ and Ca are mostly influenced by annual variations. The seasonal variation in the Ca⁺ and Ca layers in Beijing exhibits similarities to that of Kühlungsborn (54°N). While the peak density of Ca⁺ in Beijing are similar to those observed in Kühlungsborn, the peak density of the Ca layer in Beijing is about half of that reported in the Ca layer at 54°N. We provide an explanation for the disparities in the column abundance and centroid altitude of the Ca layer between Yanqing and Kühlungsborn, discussing variations in neutralization among different metal ions.

Based on the resonance fluorescence scattering mechanism, a narrowband sodium (Na) lidar can measure temperature and wind in the mesosphere and lower thermosphere (MLT) region. By using a narrowband spectral filter, background light noise during the day can be suppressed, allowing for continuous observations. To obtain full-diurnal-cycle temperature and wind measurement results, a complex and precise retrieval process is required, along with necessary corrections to minimize measurement errors. This paper introduces the design of a data acquisition unit for three frequencies in three directions of the Na lidar system in the Chinese Meridian Project (Phase II) and investigates the calibration and retrieval methods for obtaining diurnal temperature and horizontal wind in the MLT region, using a Na Doppler lidar with Faraday anomalous dispersion optical filter (FADOF). Furthermore, these methods are applied to observations conducted by a Na lidar in Beijing, China. The wind and temperature results over full diurnal cycles obtained from the all-solid-state Na Doppler lidar are reported for the first time and compared with temperature measurements from satellite, as well as wind observations from a meteor radar. The comparison demonstrates a reasonable agreement between the results, indicating the rationality of the lidar-retrieved results and the feasibility and effectiveness of the data correction and retrieval method.

Resonance fluorescence scattering is the physical mechanism with which lidar detects atmospheric metal layers. The resonance fluorescence scattering cross section is an important parameter for lidar data processing. In this work, the resonance fluorescence backscattering cross sections of most detectable metal atoms and ions in the atmosphere were calculated. The calculated maximum backscattering cross section of Na at the D₂ line is 7.38 × 10⁻¹⁷ m²/sr; K at the D₁ line is 7.37 × 10⁻¹⁷ m²/sr; Fe at the 372 nm line is 7.53 × 10⁻¹⁸ m²/sr; Fe at the 374 nm line is 6.98 × 10⁻¹⁸ m²/sr; Fe at the 386 nm line is 3.75 × 10⁻¹⁸ m²/sr; Ni at the 337 nm line is 4.05 × 10⁻¹⁸ m²/sr; and Ni at the 341 nm line is 2.05 × 10⁻¹⁷ m²/sr; Ca is 3.06 × 10⁻¹⁶ m²/sr; Ca⁺ is 1.12 × 10⁻¹⁶ m²/sr. The influence of the laser linewidth on the effective scattering cross section was discussed. If the laser linewidth is lower than 2 GHz to detect Na, the laser center frequency locked at the D_2a line is a better option than the D₂ line in order to obtain greater signals. If an unlocked lidar is used to detect Na, the frequency at D_2a should be used as the laser center frequency when the effective scattering cross section of Na was calculated, because the absorption cross section of Na atom has two local maxima. This work proposes a quantifiable comparative method for assessing the observation difficulty of different metal particles by comparing their relative uncertainties in lidar observation. It is assumed that under the same observation conditions, the detectability of different metal atoms and ions is compared. Using Na as a basis for comparison, the relative uncertainty of Ni at 337 nm is the highest, about a factor of 21 larger than that of Na, indicating that it is the most difficult to be detected. The purpose of this work is to present a quantifiable comparison method for the detection difficulty of the metal particles by lidar in the middle and upper atmosphere, which has great significance for the design of the lidar system.

Based on the established LIDAR chain along the 120°E meridian in China, the gravity wave (GW) activity between 80 and 105 km and the seasonal behavior of temporal and spatial spectra at Beijing, Hefei and Hainan were studied with three years of continued observations. The averaged GW-induced atmospheric density perturbations are near 6%, which in summer are obviously larger than in winter. The semiannual maxima occur near the solstice and the minimum emerges around the equinox at different latitudes. Besides, as a disparity, the density perturbation of GW is still active considerably in winter at low latitude at Hainan. The spectra of vertical wave number Fa(m) and observed frequency Fa(ω) show power law shapes, of which the average is near −3 and −1.7, respectively, and both spectra with special values all exhibit similar seasonal behavior as the atmospheric density perturbations shows. This behavior is explained by multiple effects possibly originating from Tibet plateau (TP) and the main GW source in China was roughly calculated by the LIDAR observation method for the first time located at the TP boundary.

Lidar observations of metal layers play a significant role in research on the chemistry and dynamics of the mesosphere and lower thermosphere. This work reports on Fe lidar observations conducted in Beijing and Mohe. Utilizing the same laser emission system, a 1064 nm seed laser was injected into an Nd: YAG laser to generate a single longitudinal-mode pulse 532 nm laser, which pumped a dye laser to produce a 572 nm laser. The 572 nm laser and the remaining 1064 nm fundamental frequency laser passed through a sum–frequency module to generate a 372 nm laser to detect the Fe layer. According to a total of 52.6 h of observations for 10 nights in Beijing, the Fe layer has an average column density of 1.24 × 10¹⁰ cm⁻², an RMS width of 4.4 km and a centroid altitude of 89.4 km. In Mohe, observed for 16 nights and a total of 91.5 h, the Fe layer has an average column density of 1.08 × 10¹⁰ cm⁻², an RMS width of 4.6 km and a centroid altitude of 89.5 km. The probability of the occurrence of sporadic Fe layers was 42.4% in Beijing and 29.4% in Mohe. Compared to simultaneously observed Na layers, the occurrence probabilities of sporadic Fe layers were higher than those of sporadic Na layers in both stations. Based on the two cases observed in Beijing, it is conjectured that the formation mechanism of sporadic metal layers above approximately 100 km has a more significant influence on sporadic Fe layers than on sporadic Na layers. The lower thermospheric Fe layers with densities significantly larger than those of the main layer were observed during two nights in Mohe. This work contributes to the refinement of the global distribution of Fe layers and provides abundant observational data for the modeling and study of the metal layers.