The development of antireflection coatings is crucially important to improve the performance of various photonic devices, for example, to increase the efficiency of harmonic generators based on high-refractive index crystals with significant Fresnel losses. A promising technique for the reducing of radiation reflection is to change the refractive index by fabrication of antireflection microstructures (ARM) on the surface. This paper presents the results of ARM direct writing on the surfaces of a nonlinear GaSe crystal (of ε modification, according to Raman and photoluminescence spectroscopy data) using fs laser radiation and a multiples approach. An increase in transmission from 65% to 80% for an ARM fabricated on one side of the crystal and up to 94% for ARMs fabricated on both sides is demonstrated. The increase in transmission with the increasing pulse energy, as well as with an increase in the number of pulses used for the formation of a single crater, is shown. The experimental results of ARM transmission of GaSe are in qualitative agreement with the simulation results based on the measured profiles and morphology of the ARM structures.
A technique of single-longitudinal-mode selection in a fiber laser by means of a fiber multiple-beam reflection interferometer (FRI) has been experimentally demonstrated for the first time. The laser is based on a semiconductor optical amplifier placed in a linear fiber cavity formed by a fiber Bragg grating (FBG), and the FRI generates at 1529.24 nm with output power of 1 mW in single-frequency regime with a linewidth of about 217 kHz and polarization extinction ratio of >30 dB. The FRI technique potentially enables fast tuning (within the FBG bandwidth of ~0.9 nm in our case) by varying the base length of the FRI that can be used in a number of practical applications.
A new variant of all-fiber multiple-beam interferometer capable to perform narrow-band filtration of a reflected light, with characteristics similar to those for Fabry-Perot interferometer in a transmission, is presented. The interferometer design accompanied with parameters simulation is conducted, the experimental sample is fabricated and the study of its characteristics is undertaken. Experimental results conform the calculations. This variant of reflection interferometer can be used as one of laser cavity mirrors providing frequency selection of low-powered fiber lasers and laser diodes with short linear cavities. We assume, that this device makes it possible to obtain single-frequency operation with fast continuous tuning of a laser wavelength in a wide spectral range.
Experimental method of temperature and strain discrimination with fiber Bragg gratings (FBGs) sensors embedded in carbon fiber-reinforced plastic is proposed. The method is based on two-fiber technique, when two FBGs inscribed in different fibers with different sensitivities to strain and/or temperature are placed close to each other and act as a single sensing element. The nonlinear polynomial approximation of Bragg wavelength shift as a function of temperature and strain is presented for this method. The FBGs were inscribed with femtosecond laser by point-by-point inscription technique through polymer cladding of the fiber. The comparison of linear and nonlinear approximation accuracies for array of embedded sensors is performed. It is shown that the use of nonlinear approximation gives 1.52 times better accuracy. The obtained accuracies of temperature and strain measurements are 2.63.8°C and 5083με in temperature and strain range of 30120°C and 0400με, respectively. Experimental method of temperature and strain discrimination with fiber Bragg gratings (FBGs) sensors embedded in carbon fiber-reinforced plastic is proposed. The method is based on two-fiber technique, when two FBGs inscribed in different fibers with different sensitivities to strain and/or temperature are placed close to each other and act as a single sensing element. The nonlinear polynomial approximation of Bragg wavelength shift as a function of temperature and strain is presented for this method. The FBGs were inscribed with femtosecond laser by point-by-point inscription technique through polymer cladding of the fiber. The comparison of linear and nonlinear approximation accuracies for array of embedded sensors is performed. It is shown that the use of nonlinear approximation gives 1.52 times better accuracy. The obtained accuracies of temperature and strain measurements are 2.63.8°C and 5083με in temperature and strain range of 30120°C and 0400με, respectively.
A new method for the selection of the radial modes of a spherical microresonator by the quality factor, based on the effect of absorption in a thin metal film deposited on a sphere together with a dielectric layer, is proposed. The method was proved by numerical simulation on the example of the second and third radial modes , = 455, = 2, 3 selection in 80 μm radius quartz microsphere with 5 nm thick nickel film. The structure of the metal-dielectric coating was determined using analytical formulas in such a way that the metal film was placed at the node of the selected mode E-field distribution. The finite element method was used to refine the calculation, optimizing the position of the film in terms of obtaining the maximum quality factor. As a result, it was shown that the selected mode could have a relatively high quality factor (~107), while the other radial modes are significantly suppressed (~103). In addition, it is shown that selection is carried out by the mode index number () simultaneously with selection by the radial index.