Hua Wang

Dr. Hua Wang


Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2018 in Fuel
Verified
Journal Article
Closed access
CGChaohua Guo
Chaohua Guo
XWXin Wang
Xin Wang
Hua WangHua Wang
Hua Wang
SHSheng He
Sheng He
HLHong Liu
Hong Liu
PZPeng Zhu
Peng Zhu

1 May 2016 in The Journal of the Acoustical Society of America
Verified
Journal Article
Closed access
Hua WangHua Wang
Hua Wang
GTGuo Tao
Guo Tao
XSXuefeng Shang
Xuefeng Shang
Well cementation is important for oil/gas production, underground gas storage, and CO2 storage, since it isolates the reservoir layers from aquifers to increase well integrity and reduce environmental footprint. This paper analyzes wave modes of different sonic/ultrasonic methods for cement bonding evaluation. A Two dimensional finite difference method is then used to simulate the wavefield for the ultrasonic methods in the cased-hole models. Waveforms of pulse–echo method from different interfaces in a good bonded well are analyzed. Wavefield of the pitch–catch method for free casing, partial or full bonded models with ultra-low density cement are studied. Based on the studies, the modes in different methods are considered as follows: the zero-order symmetric Leaky–Lamb mode (S0) for sonic method, the first-order symmetric Leaky–Lamb mode (S1) for the pulse–echo method, and the zero-order anti-symmetric Leaky–Lamb mode (A0) for the pitch–catch method. For the sonic method, a directional transmitter in both the azimuth and axial directions can generate energy with a large incidence angle and azimuth resolution, which can effectively generate S0 and break out the azimuth limitation of the conventional sonic method. Although combination of pulse–echo and pitch–catch methods can determine the bonding condition of the third interface for the ultra-low density cement case, the pitch–catch cannot tell the fluid annulus thickness behind casing for the partial bonded cased-hole.

1 May 2016 in Journal of Natural Gas Science and Engineering
Verified
Journal Article
Closed access
Hua WangHua Wang
Hua Wang
MLMeng Li
Meng Li
XSXuefeng Shang
Xuefeng Shang

1 September 2015 in Journal of Petroleum Science and Engineering
Verified
Journal Article
Closed access
Hua WangHua Wang
Hua Wang
GTGuo Tao
Guo Tao
XSXuefeng Shang
Xuefeng Shang

19 August 2015 in The Open Petroleum Engineering Journal
Verified
Journal Article
Open access
PDF file
MLMeng Li
Meng Li
Hua WangHua Wang
Hua Wang
GTGuo Tao
Guo Tao
Distributed Acoustic Sensing (DAS) is a novel technique with low cost, no production deferment, complete coverage and repeatability for seismic data acquisition in vertical seismic profile (VSP), hydraulic fracturing monitoring, well and reservoir surveillance and micro-seismic detection. In this paper, we give a review on the field applications of DAS and the corresponding pre-processing methods as well as the limitations that hinder its further applications in exploration and production. Finally, future developments for DAS are discussed, including the enhancement of S/N ratio, precise determination of receiver channels in depth, rapid processing of massive data and integrated interpretation of multi-mode optical fiber.

12 October 2017 in Geophysical Journal International
Verified
Journal Article
Closed access
PDF file
Hua WangHua Wang
Hua Wang
MFMichael Fehler
Michael Fehler
The bonding quality of the seal formed by the cement or collapse material between casing and formation rock is critical for the hydraulic isolation of reservoir layers with shallow aquifers, production and environmental safety, and plug and abandonment issues. Acoustic logging is a very good tool for evaluating the condition of the bond between different interfaces. The understanding of the acoustic logging wavefields in wells with single casing is still incomplete. We use a 3-D finite difference method to simulate wireline monopole wavefields in a single cased borehole with different bonding conditions at two locations: (1) between the cement and casing and (2) between the cement and formation. Pressure snapshots and waveforms for different models are shown, which allow us to better understand the wave propagation. Modal dispersion curves and data processing methods such as velocity–time semblance and dispersion analysis facilitate the identification of propagation modes in the different models. We find that the P wave is submerged in the casing modes and the S wave has poor coherency when the cement is replaced with fluid. The casing modes are strong when cement next to the casing is partially or fully replaced with fluid. The amplitude of these casing modes can be used to determine the bonding condition of the interface between casing and cement. However, the limited variation of the amplitude with fluid thickness means that amplitude measurements may lead to an ambiguous interpretation. When the cement next to the formation is partially replaced with fluid, the modes propagate in the combination of steel casing and cement and the velocities are highly dependent on the cement thickness. However, if the cement thickness is large (more than 2/3 of the annulus between casing and rock), the arrival time of the first arrival approximates that of the formation compressional wave when cement is good. It would highly likely that an analyst could misjudge cement quality because the amplitudes of these modes are very small and their arrival times are very near to the formation P arrival time. It is possible to use the amplitude to estimate the thickness of the cement sheath because the variation of amplitude with thickness is strong. While the Stoneley mode (ST1) propagates in the borehole fluid, a slow Stoneley mode (ST2) appears when there is a fluid column in the annulus between the casing and formation rock. The velocity of ST2 is sensitive to the total thickness of the fluid column in the annulus independent of the location of the fluid in the casing annulus. We propose a full waveform method, which includes the utilization of the amplitude of the first arrival and also the velocity of the ST2 wave, to estimate the bonding condition of multiple interfaces. These two measurements provide more information than the current method that uses only the first arrival to evaluate the bonding interfa next to the casing.