Youliang Zhang

Dr. Youliang Zhang


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 June 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
ZWZhijia Wang
Zhijia Wang
HLHaojie Li
Haojie Li
SDShusu Duan
Shusu Duan
ZFZhisheng Feng
Zhisheng Feng
YZYouliang Zhang
Youliang Zhang
JZJianjing Zhang
Jianjing Zhang
The alkali-activated composites technique is a promising method for the in situ preparation of cavity filling/grouting materials from engineering waste soil. To investigate the feasibility of engineering waste soil utilization by the alkali activation process, the macroscopic and microscopic properties of the fly ash/slag-based alkali-activated composites, after solidification/stabilization (S/S) with sandy clay excavated at Baishitang Station of Shenzhen Metro, were studied. The unconfined compressive strength (UCS) test was conducted to evaluate the S/S effect of alkali-activated composites. The results show that the optimum quality ratio of slag and fly ash correspond to 7:3, the modulus of alkaline activator to 1.3, and the alkalinity of alkaline activator to 10%. The alkali-activated composite’s strength under these parameters can reach 45.25 MPa at 3 days, 49.85 MPa at 7 days, and 62.33 MPa at 28 days. A maximum 3-day UCS of 21.71 MPa, 75% of the 28-day UCS, was achieved by an engineering waste soil and alkali-activated composites mass ratio of 5:5, slaked lime content of 4.5%, and a water-to-solid ratio of 0.26, and it can also meet the required fluidity and setting time for construction well. Fluidity is primarily affected by the soil-to-binder ratio, which decreases as the ratio decreases, while the water-to-solid ratio increases fluidity. Slaked lime has minimal impact on fluidity. The setting time is mainly influenced by the soil-to-binder ratio, followed by slaked lime content and water-to-solid ratio, with setting time shortening as the soil-to-binder ratio and slaked lime content increase, and lengthening as the water-to-solid ratio increases. Through Fourier Transform Infrared Spectroscopy (FTIR), Scanning Electron Microscopy (SEM), and Energy Dispersive Spectroscopy (EDS) tests, microscopic analysis showed that loose granular units are firmly cemented by alkali-activated composites. Based on the results of on-site grouting tests in karst caves, the alkali-activated grout materials reached a strength of 5.2 MPa 28 days after filling, which is 162.5% of the strength of cement grouting material, satisfying most of the requirements for cavity filling in Shenzhen.

21 August 2023 in Sustainability
Verified
Journal Article
Open access
PDF file
MHMingjuan Huang
Mingjuan Huang
YZYouliang Zhang
Youliang Zhang
JHJinning Hu
Jinning Hu
YHYunpeng Hei
Yunpeng Hei
ZXZikun Xu
Zikun Xu
JSJinchen Su
Jinchen Su
With the development of a free trade port on Hainan Island, the construction of tourist roads around the island is currently underway. However, the weather conditions on Hainan Island, which include strong typhoons and rainstorms, pose challenges for the construction of highway-cutting slopes on the coastal weak sandy terraces. These slopes are susceptible to sand loss and erosion from rainfall. To address this issue, MICP green spray irrigation solidification technology is used to strengthen the sandy cutting, and pore water pressure monitoring is carried out on the slope model during MICP solidification and rainfall scour. Combined with the model pore water pressure and flow slip failure pattern, a dynamic analysis was conducted. The results show that MICP sprinkler irrigation technology can solidify the surface of the slope model in a short time, and after three sets of rotation reinforcement, the model achieved a cementation depth of 4 cm, with a well-reinforced surface and closely connected sand samples. Under the erosion effect of simulated rainfall intensity, the sand loss of the slope was weakened, without damage to the sand binding, and the integrity was enhanced. The cementation between the sand grains facilitated the conversion of most of the rainfall into runoff. However, despite these efforts, the slope eventually slid after 150 s. During the sliding process, the leading edge of the slope model lost sand and became unloaded, and the failure mode was graded a creep slip failure. Finally, the slope was divided into several blocks due to the continuous expansion of cracks following the slope failure. The erosion stability of the sandy slope under heavy rains was optimized and the sand loss was prevented effectively. This study proposes a new method of MICP remediation techniques that serve as a new test basis for the practical application of MICP technology in engineering projects.

1 January 2024 in Advances in Civil Engineering
Verified
Journal Article
Open access
JXJingfeng Xiao
Jingfeng Xiao
QWQunwei Wang
Qunwei Wang
QZQianhui Zhang
Qianhui Zhang
YHYunpeng Hei
Yunpeng Hei
YZYouliang Zhang
Youliang Zhang
The utilization of numerical analytic techniques has become essential in evaluating the environmental consequences of excavation in foundation pits. The careful selection of suitable soil constitutive models has significant importance in this regard. The Hardening Soil (HS) model has become widely utilized in the numerical analysis of foundation pits among the several models considered. The essence of a constitutive model is in the identification and determination of its calculation parameters. The stress–strain curve is derived by conducting triaxial testing, utilizing the inherent properties of the particle swarm optimization (PSO) technique. The objective function entails quantifying the disparity between stress–strain curves obtained from various parameters and experimental curves while iteratively searching for five crucial parameters of soil‐hardening models: effective internal friction angle φ, effective cohesion, failure ratio Rf, stiffness level‐dependent power exponent, and standard triaxial‐drained test secant stiffness . The objective of this research is to create a computational software utilizing the Python programming language to execute PSO with the purpose of determining sets of five fundamental soil constitutive parameters. This research employs optimized parameters acquired from PSO to construct a numerical model for foundation pits and performs numerical computations. Accurate findings may be reached by comparing the measured deformation in the numerical simulation with that seen in actual foundation pits. The results demonstrate a high degree of consistency between the experimental curves and the five parameter combinations obtained through the PSO algorithm, with an error rate not exceeding 8.2%. Moreover, the optimized curves exhibit closer alignment with theoretical expectations. The settlement values calculated using a numerical model based on optimized parameters show only a 6.12% deviation from actual measurements while closely following the trend of the observed curve. This outcome has the potential to greatly alleviate the burden of conducting indoor tests and holds considerable practical value in engineering applications. The observable optimization impact of PSO also serves as evidence of its viability in improving soil constitutive parameters, providing new perspectives and sources of information for future progress in this domain.

15 June 2023 in Preprints.org
Verified
Preprint
Open access
PDF file
MHMingjuan Huang
Mingjuan Huang
YZYouliang Zhang
Youliang Zhang
JHJinning Hu
Jinning Hu
YHYenpeng Hei
Yenpeng Hei
ZXZikun Xu
Zikun Xu
JSJinchen Su
Jinchen Su
With the development of free trade port in Hainan Island, the construction of tourist roads around the island is also in full swing. Under the weather conditions of strong typhoon and rainstorm in Hainan, the highway cutting slope built on the coastal weak sandy terraces has strong sand loss and is easy to be scour by rainfall. MICP green spray irrigation solidification technology is used to strengthen the sandy cutting, and pore water pressure monitoring is carried out on the slope model during MICP solidification and rainfall scour. Combined with the model pore water pressure and flow slip failure pattern, dynamic analysis was carried out. The results show that MICP sprinkler irrigation technology can solidified the surface of the slope model in a short time, and the cementation depth of the model reaches 4cm after three sets of rotation reinforcement. The surface reinforcement effect is good, and the sand samples are closely connected. Under the erosion effect of simulated rainfall intensity, the sand loss of the slope is weakened, and no sand binding damage occurs, and the integrity is enhanced. Due to the cementation between sand grains, most of the rainfall was converted into runoff, and the slope slid after 150s. When the slope began to slip, the leading edge of the slope model lost sand and unloaded, and the failure mode was graded creep slip failure. Finally, the slope was divided into several blocks due to the continuous expansion of cracks after the slope failure. The erosion stability of the sandy slope under heavy rains is optimized and the sand loss is prevented effectively. In this study, a new method of MICP remediation techniques is proposed, which provides a new test basis for the application of MICP technology in practical engineering.

6 April 2025 in Scientific Reports
Verified
Journal Article
Open access
PDF file
QWQunwei Wang
Qunwei Wang
QLQun Li
Qun Li
YZYouliang Zhang
Youliang Zhang
Monitoring of the open caissons during the sinking process is a crucial aspect in construction projects. Traditional methods such as Electric Level have limitations in providing continuous monitoring throughout the sinking process. To address this challenge, this paper introduces a novel approach utilizing computer vision and linear intensity change model for 3D reconstruction of open caissons and real-time monitoring of the caisson sinking. In this proposed approach, RGB-D camera was firstly calibrated for the intrinsic and extrinsic parameters. Then 3D coordinates of the open caisson were obtained via the calibrated IR sensors of RGB-D camera. Subsequently, the spatial visual image of the open caisson for display was calculated using RGB sensors and the 3D coordinates. During sinking, multiple RGB sensors combined with a linear intensity change model were used for monitoring settlement displacement. The spatial visual image of the open caisson was updated with the data of the settlement and out-plane displacement. The feasibility and effectiveness of the proposed approach are validated by examples. This innovative monitoring solution has the potential to revolutionize the construction process in open caisson, ensuring timely detection of any deviations and facilitating proactive decision-making for optimal project outcomes.

26 February 2026 in Applied Sciences
Verified
Journal Article
Open access
PDF file
HLHongxi Li
Hongxi Li
YSYonghui Su
Yonghui Su
Zhiping LiZhiping Li
Zhiping Li
YZYouliang Zhang
Youliang Zhang
During the excavation process of the foundation pit, soil parameters evolve dynamically. In order to improve the accuracy of soil parameter selection in foundation pit engineering and achieve accurate deformation prediction, this paper proposes a displacement inverse analysis method that combines the enhanced starfish optimization algorithm (ESFOA) and the hybrid kernel least squares support vector machine (LSSVM). The ESFOA improves the global search capability and convergence accuracy of the starfish optimization algorithm (SFOA) by optimizing the initial population and introducing a hunting mechanism. On this basis, the ESFOA was used to optimize the RBF kernel function width (σ), polynomial kernel coefficient (q), regularization penalty coefficient (c), and kernel function mixing weight (λ) of the hybrid kernel LSSVM model. Samples were obtained through finite element simulation and orthogonal experiments, and the optimized ESFOA-LSSVM model was used to establish the nonlinear mapping relationship between the horizontal displacement of the foundation pit excavation enclosure and the soil parameters. The horizontal displacement monitoring data of the foundation pit retaining structure is used to invert the soil parameters and predict the deformation of the retaining structure under subsequent conditions. The results show that (1) compared with other algorithms, the ESFOA has good global search capabilities and convergence accuracy; (2) the ESFOA-LSSVM model is tested through test samples, and the model has good accuracy and feasibility; (3) the parameters obtained by the inversion can effectively improve the prediction accuracy of foundation pit deformation, and the prediction results are closer to the actual monitoring values.