Conventional vehicle electronic stability control requires one steering-wheel angle sensor, one lateral acceleration sensor and one yaw rate sensor to obtain a good control performance. The control system stops working when a sensor fault is detected, which means that the vehicle runs in an unprotected state. Thus, various sensor fault diagnosis algorithms have been designed to detect and isolate the faulty sensor, but these algorithms also can be used for fault-tolerant control to preserve the safety of the vehicle. However, determining which of the different sensors is faulty is very difficult as the conventional residual comparison algorithm can only find the existence of a sensor fault but cannot locate the faulty sensor, and very few research studies have focused on this problem. In this paper, an ingenious sensor fault diagnosis algorithm is proposed. The sensor fault is detected, located and isolated by cross-checking with three different yaw rate estimates. The steering-wheel angle observer and the lateral acceleration observer are designed to provide corresponding estimated sensor signals which are employed to estimate the different yaw rates by using an extended Kalman filter. A novel decision-making process is carefully designed to locate the faulty sensor based on the different yaw rate residuals. Electronic stability control is not interrupted as the faulty sensor signal is reconfigured by the estimated signal. Experimental tests on a real car show that the proposed algorithm is efficient for detecting the sensor fault and identifying which sensor is faulty. Simulations show that the vehicle stability control strategy based on the proposed sensor fault-tolerant control algorithm has a better performance than the traditional control strategy does.
The safety performance test of intelligent driving vehicles needs to rely on the collision scenarios in a real road traffic environment. In order to study the collision scenarios and accident characteristics of vehicles and two wheelers (TWs) in line with the complex traffic conditions in China, this paper proposes using clustering analysis to initially cluster traffic accident data to obtain the base scenarios and then applying the association rule algorithm to each base scenario to obtain the potential connection of its accident attributes and describe the collision scenarios in more detail. This study is based on data from 335 vehicle and two-wheeler crashes in the National Automobile Accident In-Depth Investigation System (NAIS). It used clustering analysis to cluster the crash data into different partitions to obtain eight clusters of vehicle and two-wheeler base scenarios and applied association rules to analyze the rest of the accident attributes, revealing common crash characteristics to describe the base scenarios in more detail. In the end, it constructed eleven types of detailed vehicle and two-wheeler collision scenarios covering straight roads, intersections, and T-junctions. The results provide richer and more suitable crash scenarios of vehicles and two wheelers in China’s complex traffic and is an important reference for the development of intelligent driving testing scenarios in the future.
The nanoscale 0.5Li2MnO3·0.5Li(Ni0.44Mn0.44Co0.12)O2 Li-manganese-rich electrode material was synthesized by the co-precipitate method, and its electrochemical properties were systematically analyzed, especially the electrochemical impedance spectroscopy. The failure of the electrode interface and the structural transformation of the material at high potential are the main reasons for the deterioration of the Li-manganese-rich electrode, and high temperatures accelerate the deterioration. Based on the systematic analysis of the induced reactance change with electrode polarization potential, it is found that the induced reactance of a Li-manganese-rich electrode is not only related to the degree of delithiation/lithiation but also has a great relationship with the performance of the electrode/electrolyte interface. This conclusion is beneficial for the manufacturing of battery failure analysis by providing a theoretical basis for guidance.
To enhance the safety and stability of lane change maneuvers for autonomous vehicles in adverse weather conditions, this paper proposes a quadratic programming−based trajectory planning algorithm for lane changing in rainy weather. Initially, in order to mitigate the risk of potential collisions on wet and slippery road surfaces, we incorporate the concept of road adhesion coefficients and delayed reaction time to refine the establishment of the minimum safety distance. This augmentation establishes constraints on lane change safety distances and delineates the boundaries of viable lane change domains within inclement weather contexts. Subsequently, adopting a hierarchical trajectory planning framework, we incorporate visibility cost functions and safety distance constraints during dynamic programming sampling to ensure the safety of vehicle operation. Furthermore, the vehicle lane change sideslip phenomenon is considered, and the optimal lane change trajectory is obtained based on the quadratic programming algorithm by introducing the maneuverability objective function. In conclusion, to verify the effectiveness of the algorithm, lateral linear quadratic regulator (LQR) and longitudinal double proportional−integral−derivative (DPID) controllers are designed for trajectory tracking. The results demonstrate the algorithm’s capability to produce continuous, stable, and collision−free trajectories. Moreover, the lateral acceleration varies within the range of ±1.5 m/s2, the center of mass lateral deflection angle varies within the range of ±0.15°, and the yaw rate remains within the ±0.1°/s range.
18 February 2019 in IOP Conference Series: Materials Science and Engineering
Usability is a decisive factor of any child safety restraint (child-safety chair) in assessing its functions, making purchase decision, and using it properly and effectively. The article takes advantage of well-developed child chair evaluation regulations and processes worldwide, itemizes and discusses every correlation between usability evaluation index and misuse, and thus formulates usability evaluation indexes system consisting of symbol usability, usability of user manual, usability of child protection and usability of chair installation; builds AEMV synthetic weight assignment modeling combining AHP method, Entropy method and Mean Variance method, on account of usability evaluation that can be subjectively biased, and index weighting that can not be decided properly, in consideration of expertise and objective test data; and calculates any index weight assigned to child chair usability evaluation based on the present synthetic weight assignment modeling, and justifies the scientific strength and objectivity of the weights assignment method in question by means of result comparison and analysis.
Defect identification is the fundamental prerequisite for the vehicle recall, the previous precedents can serve as the most direct and effective evidences for the following defect identification. This paper explores a defect identification method on the basis of case-based-reasoning, and develops the reasoning database consisting of the typical recall cases and defect modes which take automobile brake system as an example, and then a new defect identification process is proposed. This study provides a practical defect identification method based on the case-based reasoning, and assures the defect judgement is appropriate with uniform standard.