Jan Olek

Dr. Jan Olek

orcid

Research Focus & Metrics

Academic Career Length

23Years (2004-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

1 February 2008 in Journal of Materials in Civil Engineering
Verified
Journal Article
Closed access
SPSulapha Peethamparan
Sulapha Peethamparan
JOJan Olek
Jan Olek
The feasibility of using cement kiln dusts (CKDs) as potential stabilizing agents for Na-montmorillonite clay was investigated using a suite of four CKDs with different chemical and physical characteristics. The Atterberg limits, pH values, unconfined compressive strengths (UCSs), stiffnesses (stress-strain behavior), and stability of the CKDs-modified Na-montmorillonite clay were measured as functions of CKDs content and curing periods. These properties were compared with those of the untreated clay to determine the extent of enhancement, which was used as a measure of effectiveness of CKDs as stabilizers. All CKDs considerably decreased the plasticity index, thereby improving the workability of the clay, while they also considerably increased the initial pH value of clay, providing a favorable environment for further chemical (pozzolanic) reaction. The addition of CKDs and subsequent compaction substantially increased the UCS and the stiffness of the clay, thus improving its structural properties. The e...

31 December 2013
Verified
Report
Open access
PDF file
KVKho Pin Verian
Kho Pin Verian
NWNancy Whiting
Nancy Whiting
JOJan Olek
Jan Olek
JJJitendra Jain
Jitendra Jain
MSMark Snyder
Mark Snyder
The main objective of this project was to evaluate the effects of using aggregate produced from crushed concrete pavement as a replacement for natural (virgin) coarse aggregate in pavement mixtures. A total of ten different concrete mixtures containing recycled concrete aggregate (RCA) were designed to meet the requirements of Indiana Department of Transportation (INDOT) specifications. These included three different RCA replacement levels (30%, 50% and 100% by weight of the natural coarse aggregate) and two different cementitious systems (plain system – Type I portland cement only and fly ash system – 80% of Type I portland cement and 20% of ASTM C 618 Class C fly ash). The scope of the project included the evaluation and comparison of several properties of RCA and natural aggregates, evaluation and analysis of the effects of RCA on concrete properties, and modification of aggregate gradations and mixture composition in an attempt to improve the properties of RCA concrete. All ten mixtures were first produced in the laboratory (trial batches) and were subsequently reproduced in the commercial ready-mixed concrete plant. Each mixture produced in the ready-mixed plant was used to prepare several types of specimens for laboratory testing. The tests performed on fresh concrete included determination of slump and entrained air content. The mechanical properties of the hardened concrete were assessed by conducting compressive strength, flexural strength, modulus of elasticity and Poisson’s ratio tests. Concrete durability was assessed using a wide array of measurements, including: rapid chloride permeability (RCP), rapid chloride migration (RCM), electrical impedance spectroscopy (EIS), surface resistivity, free shrinkage, water absorption test, freeze-thaw resistance and scaling resistance. The test results indicated that the properties of plain (no fly ash) concrete mixtures with 30% RCA as coarse aggregate were very comparable to (in some cases even better than) those of the control concrete (0% RCA). Although mixtures with 50% RCA showed a reduction in durability and mechanical properties of up to 36%, the test results still met INDOT’s specifications requirements. The mechanical properties of plain concretes made with 100% RCA were measurably lower (16%-25%) than those of the control concrete. It should be pointed out, however, that these properties were still above the minimums required by INDOT’s specifications except for one mixture in which the w/c was increased to 0.47 to achieve workability. The use of fly ash improved the strength and durability of RCA concrete, especially at later ages. In particular, the properties

18 January 2022 in The Plant Journal
Verified
Journal Article
Closed access
PDF file
ESEvan E. Sowinski
Evan E. Sowinski
BWBryce M. Westman
Bryce M. Westman
CRCeleste R. Redmond
Celeste R. Redmond
YKYingzhen Kong
Yingzhen Kong
AOAnna T. Olek
Anna T. Olek
NCNicholas C. Carpita
Nicholas C. Carpita

23 July 2024 in Construction and Building Materials
Verified
Journal Article
Closed access
RARoshan Muththa Arachchige
Roshan Muththa Arachchige
JOJan Olek
Jan Olek
FRFarshad Rajabipour
Farshad Rajabipour
SPSulapha Peethamparan
Sulapha Peethamparan

1 July 2012 in Journal of Materials in Civil Engineering
Verified
Journal Article
Closed access
MMMaria Marks
Maria Marks
DJDaria Jozwiak-Niedzwiedzka
Daria Jozwiak-Niedzwiedzka
MGMichal A. Glinicki
Michal A. Glinicki
JOJan Olek
Jan Olek
MMMichal Marks
Michal Marks
The objective of this investigation was to develop rules for automatic assessment of concrete quality by using selected artificial intelligence methods based on machine learning. The range of tested materials included concrete containing nonstandard waste material—the solid residue from coal combustion in circulating fluidized bed combustion boilers (CFBC ash) used as an additive. Performed experimental tests on the surface scaling resistance provided data for learning and verification of rules discovered by machine learning techniques. It has been found that machine learning is a tool that can be applied to classify concrete durability. The rules generated by computer programs AQ21 and WEKA by using the J48 algorithm provided a means for adequate categorization of plain concrete and concrete modified with CFBC fly ash as materials resistant or not resistant to the surface scaling.