In this study, the effects of negative valve overlap (NVO) on homogenous charge compression ignition (HCCI) combustion and engine performance were experimentally investigated. A four stroke, single cylinder, port injection HCCI engine was operated at −16 deg crank angle (CA), −8 deg CA, and +8 deg CA valve overlap values and different lambda values and engine speeds at wide open throttle. RON40 and RON60 were used as test fuels in view of combustion and performance characteristics in HCCI mode. The variations of indicated mean effective pressure (IMEP), residual gas, CA50, indicated thermal efficiency (ITE), indicated specific fuel consumption (ISFC), maximum pressure rise rate (MPRR) and ringing intensity (RI) were observed on HCCI combustion. The results showed that NVO caused to trap residual gases in the combustion chamber. Hot residual gases showed heating and dilution effect on HCCI combustion. Combustion was retarded with the presence of residual gas at −16 deg CA NVO. Test results showed that higher imep and maximum in-cylinder pressure were obtained with RON60 according to RON40. As expected, CA50 was obtained later with RON60 compared to RON40 due to more resistance of auto-ignition. RON60 residual gas prevented the rapid and sudden combustion due to higher heat capacity of charge mixture. RI decreased with the usage of RON60 compared to RON40. Significant decrease was seen on RI with RON60 especially at lower lambda values. It was seen that HCCI combustion can be controlled with NVO and operating range of HCCI engines can be extended.

Reactivity Controlled Compression Ignition (RCCI), which is a low temperature combustion mode based on the principle of working with dual fuel, has attracted the attention of researchers in recent years due to its advantages such as high thermal efficiency, low NOx and soot emissions, and controllability of combustion. In this study, the effects of injection timing and lambda on RCCI combustion mode were investigated numerically by validating the experimental data with Converge CFD software. A four-cylinder, four-stroke gasoline direct-injection engine with a compression ratio of 9.2 was used in RCCI combustion mode at an engine speed of 1000 rpm. The maximum cylinder pressure also increased and RCCI combustion was advanced while the injection timing was advanced. The highest peak pressure was obtained at SOI=-50°CA aTDC, and the lowest peak pressure was obtained at SOI=-25°CA aTDC. Similarly, the highest peak HRR value was acquired as 213 J/°CA at SOI=-50°CA aTDC. It has been observed that as the lambda decreases, the maximum cylinder pressure increases, and combustion advances. In addition, the heat release rises with a decrease in lambda value. The maximum heat release rate was acquired as 77.91 J/°CA at λ=1.2. The results show that injection timing and lambda have a great influence on RCCI combustion mode and the combustion phase can be controlled with these parameters.

In this numerical study, the effects of the premixed ratio, intake manifold pressure and intake air temperature on a four-cylinder, four-stroke, direct injection, low-compression-ratio gasoline engine, operated in reactivity-controlled compression ignition (RCCI) combustion mode at a constant engine speed of 1000 rpm, were investigated using Converge CFD software. The results of numerical analyses showed that the maximum in-cylinder pressure and heat release rate (HRR) increased and the combustion phase advanced depending on the rise in both intake manifold pressure and intake air temperature. The CA50 shifted by 18.5 °CA with an increment in the intake air temperature from 60 °C to 100 °C. It was observed that the combustion duration dropped from 44 °CA to 38 °CA upon boosting the intake manifold pressure from 103 kPa to 140 kPa. Moreover, a delay in the combustion phase occurred at a constant intake air temperature with an increasing premixed ratio. The maximum value of in-cylinder pressure was recorded as 36.15 bar (at 11 °CA aTDC) with the use of PRF20. Additionally, as the content of iso-octane in the fuel mixture was increased, combustion delay occurred, and the maximum value of in-cylinder temperature obtained was 11 °CA aTDC using PRF20 fuel at the earliest point. While HC and CO emissions reached the highest values at a 60 °C intake air temperature, NO_x and soot emission values were detected at quite low levels at this temperature. The values of all these emissions increased with rising intake manifold pressure and reached their highest values at 140 kPa. In addition, while the highest HC and CO emission values were observed with the use of PRF60 fuel, the results revealed that the control of the combustion phase in the RCCI strategy is notably affected by the premixed ratio, intake manifold pressure and intake air temperature.