Nowadays, solid polymer electrolytes have attracted increasing attention for their wide electrochemical stability window, low cost, excellent processability, flexibility and low interfacial impedance. Specifically, gel polymer electrolytes (GPEs) are attractive substitutes for liquid ones due to their high ionic conductivity (10⁻³–10⁻² S cm⁻¹) at room temperature and solid-like dimensional stability with excellent flexibility. These characteristics make GPEs promising materials for electrochemical device applications, i.e., high-energy-density rechargeable batteries, supercapacitors, electrochromic displays, sensors, and actuators. The aim of this study is to demonstrate the viability of a sustainable GPE, prepared without using organic solvents or ionic liquids and with a simplified preparation route, that can substitute aqueous electrolytes in electrochemical devices operating at low voltages (up to 2 V). A polyvinyl alcohol (PVA)-based GPE has been cast from an aqueous solution and characterized with physicochemical and electrochemical methods. Its electrochemical stability has been assessed with capacitive electrodes in a supercapacitor configuration, and its good ionic conductivity and stability in the atmosphere in terms of water loss have been demonstrated. The feasibility of GPE in an electrochemical sensor configuration with a mediator embedded in an insulating polymer matrix (ferrocene/polyvinylidene difluoride system) has also been reported.

Biopolymers emerged in recent years as a promising alternative for a more sustainable manufacturing of electrochemical energy storage systems. In fact, for environmentally friendly aqueous systems, fluorinated polymers are usually adopted. For this reason, substituting these polymers with water processable binders could improve the overall environmental impact of the device. In this study, a low – cost and environmentally friendly modification of chitosan binder for self‐standing activated carbon electrodes operating in Na ion, aqueous electrochemical double layer capacitors is reported and discussed.

The aim of this paper is to provide a historical and scientific overview of the battery world, from the disrupting discovery of Alessandro Volta to the latest advances in lithium ion batteries. For sake of clarity, it has been divided into three parts: the past, the present and the future. The first part illustrates the historical path which led to the lithium ion batteries. The second part reports the main challenges to the Li ion batteries that have been and still must be faced for increasing their performance and their sustainability. In the last part, considerations about the future of lithium ion batteries are discussed, with a special focus on sustainability.

Lithium metal batteries are considered a promising technology to implement high energy density rechargeable systems beyond lithium-ion batteries. However, the development of dendritic morphology is the basis of safety and performance issues and represents the main limiting factor for using lithium anodes in commercial rechargeable batteries. In this study, the electrochemical behaviour of Li metal has been investigated in organic carbonate-based electrolytes by electrochemical impedance spectroscopy measurements and deposition/stripping galvanostatic cycling. Low amounts of tetraalkylammonium hexafluorophosphate salts have been added to the electrolytes with the aim of regulating the lithium deposition/stripping process through the electrostatic shielding effect that improves the lithium deposition. The use of NH₄PF₆ also determined good lithium deposition/stripping performance due to the chemical modification of the native solid electrolyte interphase via direct reaction with lithium.

Basic studies on concentrated solutions are becoming more and more important due to the practical industrial and geological applications. The use in redox flow batteries is one of the most important applications of these solutions. Specifically, in this paper we investigated high-concentrated copper chloro-complexes solutions with different additives. The concentration of ligands and additives affects the physicochemical and electrochemical properties of 2 M solutions of Cu(I) and Cu(II). Solutions with calcium chloride and HCl as Cl⁻ source were investigated with Cu:Cl ratios of 1:5 and 1:7, the 1:5 Cu:Cl ratio being the best performing. The substitution of calcium chloride with ammonium chloride increased the conductivity. However, while the effect on the positive electrode process was not very evident, the reversibility of the copper deposition–stripping process was greatly improved. Orthophosphoric acid could be a viable additive to decrease the complexation of calcium with chloride anions and to improve the stability of Cu(II) chloro-complexes. Absorption spectroscopy demonstrated that phosphate ions do not coordinate copper(II) but lead to a shift in the distribution of copper chloro-complexes toward more coordinated species. Electrochemically, the increased availability of chloride anions in solution stabilized the Cu(II)-rich solution and led to increased reversibility of the Cu(II)/Cu(I) redox process.

Lithium-ion batteries (LiBs) with graphite as an anode and lithiated transition metal oxide as a cathode are approaching their specific energy and power theoretical values. To overcome the limitations of LiBs, lithium metal anode with high specific capacity and low negative redox potential is necessary. However, practical application in rechargeable cells is hindered by uncontrolled lithium deposition manifesting, for instance, as Li dendrite growth which can cause formation of dead Li, short circuits and cell failure. The electrochemical behaviour of a protic additive (NH₄PF₆) in a carbonate-based electrolyte has been investigated by operando confocal Raman spectroscopy, in situ optical microscopy, and X-ray photoelectron spectroscopy, elucidating its functional mechanism. The ammonium cation promotes a chemical modification of the lithium metal anode-electrolyte interphase by producing an N-rich solid electrolyte interphase and chemically modifying the lithium surface morphology by electrochemical pitting. This novel method results in stable lithium deposition and stripping by a decreasing the local current density on the electrode, thus limiting dendritic deposition.